Re: [PATCH 12/15] ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 board file

[Abhishek Sahu]

On 2018-01-29 10:41, Sricharan R wrote:
> Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
> ---
>  arch/arm/boot/dts/Makefile                      |  1 +
>  arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts | 78
> +++++++++++++++++++++++++
>  2 files changed, 79 insertions(+)
>  create mode 100644 arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index ef5b133..b4339ae 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -729,6 +729,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
>  	qcom-ipq4019-ap.dk04.1-c5.dtb \
>  	qcom-ipq4019-ap.dk04.1-c3.dtb \
>  	qcom-ipq4019-ap.dk07.1-c1.dtb \
> +	qcom-ipq4019-ap.dk07.1-c2.dtb \
>  	qcom-ipq8064-ap148.dtb \
>  	qcom-msm8660-surf.dtb \
>  	qcom-msm8960-cdp.dtb \
> diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts
> b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts
> new file mode 100644
> index 0000000..d4ee52d
> --- /dev/null
> +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts
> @@ -0,0 +1,78 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// Copyright (c) 2017, The Linux Foundation. All rights reserved.
> +
> +#include "qcom-ipq4019-ap.dk07.1.dtsi"
> +
> +/ {
> +	model = "Qualcomm Technologies, Inc. IPQ40xx/AP-DK07.1-C2";

 s/IPQ40xx/IPQ4019

> +
> +	soc {
> +		pcie0: pci@40000000 {
> +			status = "disabled";
> +		};

 We can disable in base dtsi itself.

> +
> +		pinctrl@1000000 {
> +			serial_1_pins: serial1_pinmux {
> +				mux {
> +					pins = "gpio8", "gpio9";
> +					function = "blsp_uart1";
> +					bias-disable;
> +				};
> +			};
> +
> +			spi_0_pins: spi_0_pinmux {
> +				mux {
> +					pins = "gpio13", "gpio14",
> "gpio15";
> +					function = "blsp_spi0";
> +					bias-disable;
> +				};
> +				cs1 {
> +					pins = "gpio12";
> +					function = "gpio";
> +				};
> +				host_int1 {
> +					pins = "gpio10";
> +					function = "gpio";
> +					input;
> +				};
> +				cs2 {
> +					pins = "gpio45";
> +					function = "gpio";
> +				};
> +				host_int2 {
> +					pins = "gpio61";
> +					function = "gpio";
> +					input;
> +				};
> +				rst {
> +					pins = "gpio36";
> +					function = "gpio";
> +					output-high;
> +				};

 Normally spi pins should contains spi protocol related pins
 could you please explain what is the role of host_pin and rst
 pins and which driver will use these.

> +			};
> +		};
> +
> +		serial@78b0000 {
> +			pinctrl-0 = <&serial_1_pins>;
> +			pinctrl-names = "default";
> +			status = "ok";
> +		};
> +
> +		spi_0: spi@78b5000 { /* BLSP1 QUP1 */
> +			pinctrl-0 = <&spi_0_pins>;
> +			pinctrl-names = "default";
> +			status = "ok";

 From pinmux, it looks like multiple gpio based cs are being
 used so do we need to specify cs-gpios like dk01-c2.

 Thanks,
 Abhishek

> +
> +			spidev0_0 {
> +				compatible = "spidev";
> +				reg = <0>;
> +				spi-max-frequency = <24000000>;
> +			};
> +			spidev0_1 {
> +				compatible = "spidev";
> +				reg = <1>;
> +				spi-max-frequency = <24000000>;
> +			};
> +		};
> +	};
> +};