Re: [PATCH 09/15] ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 board file

[Sricharan R]

Hi Abhishek,

On 2/3/2018 5:07 PM, Abhishek Sahu wrote:
> On 2018-01-29 10:41, Sricharan R wrote:
>> Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
>> ---
>> Âarch/arm/boot/dts/MakefileÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ |Â 1 +
>> Âarch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts | 14 ++++++++++++++
>> Â2 files changed, 15 insertions(+)
>> Âcreate mode 100644 arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 68e4b15..0104ba2 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -727,6 +727,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
>> ÂÂÂÂ qcom-ipq4019-ap.dk01.1-c2.dtb \
>> ÂÂÂÂ qcom-ipq4019-ap.dk04.1-c1.dtb \
>> ÂÂÂÂ qcom-ipq4019-ap.dk04.1-c5.dtb \
>> +ÂÂÂ qcom-ipq4019-ap.dk04.1-c3.dtb \
>> ÂÂÂÂ qcom-ipq8064-ap148.dtb \
>> ÂÂÂÂ qcom-msm8660-surf.dtb \
>> ÂÂÂÂ qcom-msm8960-cdp.dtb \
>> diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts
>> b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts
>> new file mode 100644
>> index 0000000..7a93fc4
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts
>> @@ -0,0 +1,14 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +// Copyright (c) 2017, The Linux Foundation. All rights reserved.
>> +
>> +#include "qcom-ipq4019-ap.dk04.1.dtsi"
>> +
>> +/ {
>> +ÂÂÂ model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1-C3";
>> +
>> +ÂÂÂ soc {
>> +ÂÂÂÂÂÂÂ nand: qpic-nand@79b0000 {
>> +ÂÂÂÂÂÂÂÂÂÂÂ status = "disabled";
>> +ÂÂÂÂÂÂÂ };
> 
> ÂNormally we need to disable in base dtsi and enable in
> Âboard dtsi so that base dtsi will always work in all the
> Âboards. Now If We load the base dtsi in any DK04 board
> Âother than C1, then nand failure will come.

 Hmm, qpic nand is not there only on C3 and available in rest
 of dk04-c* variants. So it should work, downstream also
 does it in same way. Anyways, from a readability point, feel that
 better to make these uncommon configurations in each board file
 specifically rather than putting in common file and changing like this.

Regards,
 Sricharan


-- 
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation