Re: [PATCH 3/3] ARM: dts: sun7i: Add support for the Ainol AW1 tablet

From: Paul Kocialkowski
Date: Tue Apr 10 2018 - 17:35:46 EST

Le mardi 10 avril 2018 Ã 23:31 +0200, Paul Kocialkowski a Ãcrit :
> This adds support for the Ainol AW1, an A20-based 7" tablet from
> Ainol.

This version didn't use the dedicated binding for the panel and will be
fixed in v2 and onwards.

> The following board-specific features are supported:
> * LCD panel
> * Backlight
> * USB OTG
> * Buttons
> * Touchscreen (doesn't work without non-free firmware)
> * Accelerometer
> * Battery
>
> The following are untested:
> * Audio output
> * Audio speakers
> * USB via SPCI connector
>
> The following are not supported:
> * Wi-Fi
> * Bluetooth
> * NAND
> * Audio via SPCI connector
>
> Signed-off-by: Paul Kocialkowski <contact@xxxxxxxx>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts | 358
> ++++++++++++++++++++++++++++++
> 2 files changed, 359 insertions(+)
> create mode 100644 arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 9f7133b6fba0..03bfacebfdbd 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -929,6 +929,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
> sun6i-a31s-sinovoip-bpi-m2.dtb \
> sun6i-a31s-yones-toptech-bs1078-v2.dtb
> dtb-$(CONFIG_MACH_SUN7I) += \
> + sun7i-a20-ainol-aw1.dtb \
> sun7i-a20-bananapi.dtb \
> sun7i-a20-bananapi-m1-plus.dtb \
> sun7i-a20-bananapro.dtb \
> diff --git a/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
> b/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
> new file mode 100644
> index 000000000000..697586991aea
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
> @@ -0,0 +1,358 @@
> +/*
> + * Copyright 2018 Paul Kocialkowski <contact@xxxxxxxx>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the
> Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
> KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
> WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun7i-a20.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> + model = "Ainol AW1";
> + compatible = "ainol,ainol-aw1", "allwinner,sun7i-a20";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pinctrl-names = "default";
> + pinctrl-0 = <&backlight_enable_pin>;
> + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
> + brightness-levels = <0 10 20 30 40 50 60 70 80 90
> 100>;
> + default-brightness-level = <5>;
> + enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
> + };
> +
> + panel: panel {
> + compatible = "innolux,at070tn92";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + power-supply = <&panel_power>;
> + backlight = <&backlight>;
> +
> + port@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + panel_input: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&tcon0_out_panel>;
> + };
> + };
> + };
> +
> + panel_power: panel_power {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&panel_power_pin>;
> + regulator-name = "panel-power";
> + regulator-min-microvolt = <10400000>;
> + regulator-max-microvolt = <10400000>;
> + gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
> + enable-active-high;
> + regulator-boot-on;
> + };
> +};
> +
> +&codec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&codec_pa_pin>;
> + allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15 */
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&reg_dcdc2>;
> +};
> +
> +&de {
> + status = "okay";
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins_a>;
> + status = "okay";
> +
> + axp209: pmic@34 {
> + reg = <0x34>;
> + interrupt-parent = <&nmi_intc>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins_a>;
> + status = "okay";
> +
> + lis3dh: accelerometer@18 {
> + compatible = "st,lis3dh-accel";
> + reg = <0x18>;
> + vdd-supply = <&reg_vcc3v3>;
> + vddio-supply = <&reg_vcc3v3>;
> + st,drdy-int-pin = <1>;
> + };
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins_a>;
> + status = "okay";
> + clock-frequency = <400000>; /* 400 KHz required for GSL1680.
> */
> +
> + gsl1680: touchscreen@40 {
> + compatible = "silead,gsl1680";
> + reg = <0x40>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&touchscreen_power_pin>;
> + interrupt-parent = <&pio>;
> + interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /* EINT21
> (PH21) */
> + power-gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20
> */
> + firmware-name = "gsl1680-ainol-aw1.fw";
> + touchscreen-size-x = <480>;
> + touchscreen-size-y = <800>;
> + touchscreen-swapped-x-y;
> + touchscreen-inverted-y;
> + silead,max-fingers = <5>;
> + };
> +};
> +
> +&lradc {
> + vref-supply = <&reg_vcc3v0>;
> + status = "okay";
> +
> + button@571 {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + channel = <0>;
> + voltage = <571428>;
> + };
> +
> + button@761 {
> + label = "Volume Down";
> + linux,code = <KEY_VOLUMEDOWN>;
> + channel = <0>;
> + voltage = <761904>;
> + };
> +
> + button@952 {
> + label = "Home";
> + linux,code = <KEY_HOME>;
> + channel = <0>;
> + voltage = <952380>;
> + };
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>;
> + vmmc-supply = <&reg_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
> + cd-inverted;
> + status = "okay";
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci1 {
> + status = "okay";
> +};
> +
> +&otg_sram {
> + status = "okay";
> +};
> +
> +&pio {
> + panel_power_pin: panel_power_pin@0 {
> + pins = "PH8";
> + function = "gpio_out";
> + };
> +
> + backlight_enable_pin: backlight_enable_pin@0 {
> + pins = "PH7";
> + function = "gpio_out";
> + };
> +
> + touchscreen_power_pin: touchscreen_power_pin@0 {
> + pins = "PH20";
> + function = "gpio_out";
> + };
> +
> + codec_pa_pin: codec_pa_pin@0 {
> + pins = "PH15";
> + function = "gpio_out";
> + };
> +
> + usb0_id_detect_pin: usb0_id_detect_pin@0 {
> + pins = "PH4";
> + function = "gpio_in";
> + bias-pull-up;
> + };
> +
> + usb0_vbus_pin: usb0_vbus_pin@0 {
> + pins = "PB9";
> + function = "gpio_out";
> + };
> +
> + usb1_vbus_pin: usb1_vbus_pin@0 {
> + pins = "PH6";
> + function = "gpio_out";
> + };
> +
> + usb2_vbus_pin: usb2_vbus_pin@0 {
> + pins = "PH3";
> + function = "gpio_out";
> + };
> +};
> +
> +&pwm {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm0_pins_a>;
> + status = "okay";
> +};
> +
> +&tcon0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&lcd_rgb666_pins>;
> + status = "okay";
> +};
> +
> +&tcon0_out {
> + tcon0_out_panel: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&panel_input>;
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins_a>;
> + status = "okay";
> +};
> +
> +&usb_otg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usbphy {
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb0_id_detect_pin>;
> + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
> + usb0_vbus_power-supply = <&usb_power_supply>;
> + usb0_vbus-supply = <&reg_usb0_vbus>;
> + usb1_vbus-supply = <&reg_usb1_vbus>;
> + usb2_vbus-supply = <&reg_usb2_vbus>;
> + status = "okay";
> +};
> +
> +#include "axp209.dtsi"
> +
> +&battery_power_supply {
> + status = "okay";
> +};
> +
> +&reg_dcdc2 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1450000>;
> + regulator-name = "vdd-cpu";
> +};
> +
> +&reg_dcdc3 {
> + regulator-always-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1400000>;
> + regulator-name = "vdd-int-dll";
> +};
> +
> +&reg_ldo1 {
> + regulator-name = "vdd-rtc";
> +};
> +
> +&reg_ldo2 {
> + regulator-always-on;
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-name = "avcc";
> +};
> +
> +&reg_usb0_vbus {
> + pinctrl-0 = <&usb0_vbus_pin>;
> + status = "okay";
> +};
> +
> +&reg_usb1_vbus {
> + pinctrl-0 = <&usb1_vbus_pin>;
> + status = "okay";
> +};
> +
> +&reg_usb2_vbus {
> + pinctrl-0 = <&usb2_vbus_pin>;
> + status = "okay";
> +};
> +
> +&usb_power_supply {
> + status = "okay";
> +};
--
Paul Kocialkowski,

developer of free digital technology and hardware support.

Website: https://www.paulk.fr/
Coding blog: https://code.paulk.fr/
Git repositories: https://git.paulk.fr/ https://git.code.paulk.fr/

Attachment: signature.asc
Description: This is a digitally signed message part