Re: [linux-sunxi] Re: [PATCH 3/3] ARM: dts: sun7i: Add support for the Ainol AW1 tablet

From: Paul Kocialkowski
Date: Wed Apr 11 2018 - 02:10:19 EST

Hi,

Le mardi 10 avril 2018 Ã 23:35 +0200, Paul Kocialkowski a Ãcrit :
> Le mardi 10 avril 2018 Ã 23:31 +0200, Paul Kocialkowski a Ãcrit :
> > This adds support for the Ainol AW1, an A20-based 7" tablet from
> > Ainol.
>
> This version didn't use the dedicated binding for the panel and will
> be
> fixed in v2 and onwards.
>
> > The following board-specific features are supported:
> > * LCD panel
> > * Backlight
> > * USB OTG
> > * Buttons
> > * Touchscreen (doesn't work without non-free firmware)
> > * Accelerometer
> > * Battery
> >
> > The following are untested:
> > * Audio output
> > * Audio speakers
> > * USB via SPCI connector
> >
> > The following are not supported:
> > * Wi-Fi
> > * Bluetooth
> > * NAND
> > * Audio via SPCI connector

The camera is also not supported at this point.

> > Signed-off-by: Paul Kocialkowski <contact@xxxxxxxx>
> > ---
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts | 358
> > ++++++++++++++++++++++++++++++
> > 2 files changed, 359 insertions(+)
> > create mode 100644 arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 9f7133b6fba0..03bfacebfdbd 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -929,6 +929,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
> > sun6i-a31s-sinovoip-bpi-m2.dtb \
> > sun6i-a31s-yones-toptech-bs1078-v2.dtb
> > dtb-$(CONFIG_MACH_SUN7I) += \
> > + sun7i-a20-ainol-aw1.dtb \
> > sun7i-a20-bananapi.dtb \
> > sun7i-a20-bananapi-m1-plus.dtb \
> > sun7i-a20-bananapro.dtb \
> > diff --git a/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
> > b/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
> > new file mode 100644
> > index 000000000000..697586991aea
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/sun7i-a20-ainol-aw1.dts
> > @@ -0,0 +1,358 @@
> > +/*
> > + * Copyright 2018 Paul Kocialkowski <contact@xxxxxxxx>
> > + *
> > + * This file is dual-licensed: you can use it either under the
> > terms
> > + * of the GPL or the X11 license, at your option. Note that this
> > dual
> > + * licensing only applies to this file, and not this project as a
> > + * whole.
> > + *
> > + * a) This file is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License
> > as
> > + * published by the Free Software Foundation; either version 2
> > of
> > the
> > + * License, or (at your option) any later version.
> > + *
> > + * This file is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty
> > of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
> > the
> > + * GNU General Public License for more details.
> > + *
> > + * Or, alternatively,
> > + *
> > + * b) Permission is hereby granted, free of charge, to any person
> > + * obtaining a copy of this software and associated
> > documentation
> > + * files (the "Software"), to deal in the Software without
> > + * restriction, including without limitation the rights to use,
> > + * copy, modify, merge, publish, distribute, sublicense, and/or
> > + * sell copies of the Software, and to permit persons to whom
> > the
> > + * Software is furnished to do so, subject to the following
> > + * conditions:
> > + *
> > + * The above copyright notice and this permission notice shall
> > be
> > + * included in all copies or substantial portions of the
> > Software.
> > + *
> > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
> > KIND,
> > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
> > WARRANTIES
> > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE
> > OR
> > + * OTHER DEALINGS IN THE SOFTWARE.
> > + */
> > +
> > +/dts-v1/;
> > +#include "sun7i-a20.dtsi"
> > +#include "sunxi-common-regulators.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +#include <dt-bindings/pwm/pwm.h>
> > +
> > +/ {
> > + model = "Ainol AW1";
> > + compatible = "ainol,ainol-aw1", "allwinner,sun7i-a20";
> > +
> > + aliases {
> > + serial0 = &uart0;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + backlight: backlight {
> > + compatible = "pwm-backlight";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&backlight_enable_pin>;
> > + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
> > + brightness-levels = <0 10 20 30 40 50 60 70 80 90
> > 100>;
> > + default-brightness-level = <5>;
> > + enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7
> > */
> > + };
> > +
> > + panel: panel {
> > + compatible = "innolux,at070tn92";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + power-supply = <&panel_power>;
> > + backlight = <&backlight>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + panel_input: endpoint@0 {
> > + reg = <0>;
> > + remote-endpoint =
> > <&tcon0_out_panel>;
> > + };
> > + };
> > + };
> > +
> > + panel_power: panel_power {
> > + compatible = "regulator-fixed";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&panel_power_pin>;
> > + regulator-name = "panel-power";
> > + regulator-min-microvolt = <10400000>;
> > + regulator-max-microvolt = <10400000>;
> > + gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
> > + enable-active-high;
> > + regulator-boot-on;
> > + };
> > +};
> > +
> > +&codec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&codec_pa_pin>;
> > + allwinner,pa-gpios = <&pio 7 15 GPIO_ACTIVE_HIGH>; /* PH15
> > */
> > + status = "okay";
> > +};
> > +
> > +&cpu0 {
> > + cpu-supply = <&reg_dcdc2>;
> > +};
> > +
> > +&de {
> > + status = "okay";
> > +};
> > +
> > +&ehci0 {
> > + status = "okay";
> > +};
> > +
> > +&ehci1 {
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c0_pins_a>;
> > + status = "okay";
> > +
> > + axp209: pmic@34 {
> > + reg = <0x34>;
> > + interrupt-parent = <&nmi_intc>;
> > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> > + };
> > +};
> > +
> > +&i2c1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c1_pins_a>;
> > + status = "okay";
> > +
> > + lis3dh: accelerometer@18 {
> > + compatible = "st,lis3dh-accel";
> > + reg = <0x18>;
> > + vdd-supply = <&reg_vcc3v3>;
> > + vddio-supply = <&reg_vcc3v3>;
> > + st,drdy-int-pin = <1>;
> > + };
> > +};
> > +
> > +&i2c2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c2_pins_a>;
> > + status = "okay";
> > + clock-frequency = <400000>; /* 400 KHz required for
> > GSL1680.
> > */
> > +
> > + gsl1680: touchscreen@40 {
> > + compatible = "silead,gsl1680";
> > + reg = <0x40>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&touchscreen_power_pin>;
> > + interrupt-parent = <&pio>;
> > + interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; /*
> > EINT21
> > (PH21) */
> > + power-gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20
> > */
> > + firmware-name = "gsl1680-ainol-aw1.fw";
> > + touchscreen-size-x = <480>;
> > + touchscreen-size-y = <800>;
> > + touchscreen-swapped-x-y;
> > + touchscreen-inverted-y;
> > + silead,max-fingers = <5>;
> > + };
> > +};
> > +
> > +&lradc {
> > + vref-supply = <&reg_vcc3v0>;
> > + status = "okay";
> > +
> > + button@571 {
> > + label = "Volume Up";
> > + linux,code = <KEY_VOLUMEUP>;
> > + channel = <0>;
> > + voltage = <571428>;
> > + };
> > +
> > + button@761 {
> > + label = "Volume Down";
> > + linux,code = <KEY_VOLUMEDOWN>;
> > + channel = <0>;
> > + voltage = <761904>;
> > + };
> > +
> > + button@952 {
> > + label = "Home";
> > + linux,code = <KEY_HOME>;
> > + channel = <0>;
> > + voltage = <952380>;
> > + };
> > +};
> > +
> > +&mmc0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc0_pins_a>;
> > + vmmc-supply = <&reg_vcc3v3>;
> > + bus-width = <4>;
> > + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
> > + cd-inverted;
> > + status = "okay";
> > +};
> > +
> > +&ohci0 {
> > + status = "okay";
> > +};
> > +
> > +&ohci1 {
> > + status = "okay";
> > +};
> > +
> > +&otg_sram {
> > + status = "okay";
> > +};
> > +
> > +&pio {
> > + panel_power_pin: panel_power_pin@0 {
> > + pins = "PH8";
> > + function = "gpio_out";
> > + };
> > +
> > + backlight_enable_pin: backlight_enable_pin@0 {
> > + pins = "PH7";
> > + function = "gpio_out";
> > + };
> > +
> > + touchscreen_power_pin: touchscreen_power_pin@0 {
> > + pins = "PH20";
> > + function = "gpio_out";
> > + };
> > +
> > + codec_pa_pin: codec_pa_pin@0 {
> > + pins = "PH15";
> > + function = "gpio_out";
> > + };
> > +
> > + usb0_id_detect_pin: usb0_id_detect_pin@0 {
> > + pins = "PH4";
> > + function = "gpio_in";
> > + bias-pull-up;
> > + };
> > +
> > + usb0_vbus_pin: usb0_vbus_pin@0 {
> > + pins = "PB9";
> > + function = "gpio_out";
> > + };
> > +
> > + usb1_vbus_pin: usb1_vbus_pin@0 {
> > + pins = "PH6";
> > + function = "gpio_out";
> > + };
> > +
> > + usb2_vbus_pin: usb2_vbus_pin@0 {
> > + pins = "PH3";
> > + function = "gpio_out";
> > + };
> > +};
> > +
> > +&pwm {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pwm0_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&tcon0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&lcd_rgb666_pins>;
> > + status = "okay";
> > +};
> > +
> > +&tcon0_out {
> > + tcon0_out_panel: endpoint@0 {
> > + reg = <0>;
> > + remote-endpoint = <&panel_input>;
> > + };
> > +};
> > +
> > +&uart0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart0_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&usb_otg {
> > + dr_mode = "otg";
> > + status = "okay";
> > +};
> > +
> > +&usbphy {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&usb0_id_detect_pin>;
> > + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
> > + usb0_vbus_power-supply = <&usb_power_supply>;
> > + usb0_vbus-supply = <&reg_usb0_vbus>;
> > + usb1_vbus-supply = <&reg_usb1_vbus>;
> > + usb2_vbus-supply = <&reg_usb2_vbus>;
> > + status = "okay";
> > +};
> > +
> > +#include "axp209.dtsi"
> > +
> > +&battery_power_supply {
> > + status = "okay";
> > +};
> > +
> > +&reg_dcdc2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <1450000>;
> > + regulator-name = "vdd-cpu";
> > +};
> > +
> > +&reg_dcdc3 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <1400000>;
> > + regulator-name = "vdd-int-dll";
> > +};
> > +
> > +&reg_ldo1 {
> > + regulator-name = "vdd-rtc";
> > +};
> > +
> > +&reg_ldo2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-name = "avcc";
> > +};
> > +
> > +&reg_usb0_vbus {
> > + pinctrl-0 = <&usb0_vbus_pin>;
> > + status = "okay";
> > +};
> > +
> > +&reg_usb1_vbus {
> > + pinctrl-0 = <&usb1_vbus_pin>;
> > + status = "okay";
> > +};
> > +
> > +&reg_usb2_vbus {
> > + pinctrl-0 = <&usb2_vbus_pin>;
> > + status = "okay";
> > +};
> > +
> > +&usb_power_supply {
> > + status = "okay";
> > +};
>
> --
> Paul Kocialkowski,
>
> developer of free digital technology and hardware support.
>
> Website: https://www.paulk.fr/
> Coding blog: https://code.paulk.fr/
> Git repositories: https://git.paulk.fr/ https://git.code.paulk.fr/
>
--
Paul Kocialkowski,

developer of free digital technology and hardware support.

Website: https://www.paulk.fr/
Coding blog: https://code.paulk.fr/
Git repositories: https://git.paulk.fr/ https://git.code.paulk.fr/

Attachment: signature.asc
Description: This is a digitally signed message part