[PATCH 1/4] arcnet: com20020: Add com20020 io mapped version
From: Andrea Greco
Date: Thu May 17 2018 - 08:09:00 EST
From: Andrea Greco <a.greco@xxxxxxxxx>
Add support for com20022I/com20020, io mapped.
Signed-off-by: Andrea Greco <a.greco@xxxxxxxxx>
---
drivers/net/arcnet/Kconfig | 9 +-
drivers/net/arcnet/Makefile | 1 +
drivers/net/arcnet/arcdevice.h | 14 ++
drivers/net/arcnet/com20020-io.c | 287 +++++++++++++++++++++++++++++++++++++++
drivers/net/arcnet/com20020.c | 5 +-
5 files changed, 313 insertions(+), 3 deletions(-)
create mode 100644 drivers/net/arcnet/com20020-io.c
diff --git a/drivers/net/arcnet/Kconfig b/drivers/net/arcnet/Kconfig
index 39bd16f3f86d..85e60ed29fa8 100644
--- a/drivers/net/arcnet/Kconfig
+++ b/drivers/net/arcnet/Kconfig
@@ -3,7 +3,7 @@
#
menuconfig ARCNET
- depends on NETDEVICES && (ISA || PCI || PCMCIA)
+ depends on NETDEVICES
tristate "ARCnet support"
---help---
If you have a network card of this type, say Y and check out the
@@ -129,5 +129,12 @@ config ARCNET_COM20020_CS
To compile this driver as a module, choose M here: the module will be
called com20020_cs. If unsure, say N.
+config ARCNET_COM20020_IO
+ bool "Support for COM20020 (IO mapped)"
+ depends on ARCNET_COM20020 && !(ARCNET_COM20020_PCI || ARCNET_COM20020_ISA || ARCNET_COM20020_CS)
+ help
+ Say Y here if your custom board mount com20020 chipset or friends.
+ Supported Chipset: com20020, com20022, com20022I-3v3
+ If unsure, say N.
endif # ARCNET
diff --git a/drivers/net/arcnet/Makefile b/drivers/net/arcnet/Makefile
index 53525e8ea130..18da4341f404 100644
--- a/drivers/net/arcnet/Makefile
+++ b/drivers/net/arcnet/Makefile
@@ -14,3 +14,4 @@ obj-$(CONFIG_ARCNET_COM20020) += com20020.o
obj-$(CONFIG_ARCNET_COM20020_ISA) += com20020-isa.o
obj-$(CONFIG_ARCNET_COM20020_PCI) += com20020-pci.o
obj-$(CONFIG_ARCNET_COM20020_CS) += com20020_cs.o
+obj-$(CONFIG_ARCNET_COM20020_IO) += com20020-io.o
diff --git a/drivers/net/arcnet/arcdevice.h b/drivers/net/arcnet/arcdevice.h
index d09b2b46ab63..86c36d9b666b 100644
--- a/drivers/net/arcnet/arcdevice.h
+++ b/drivers/net/arcnet/arcdevice.h
@@ -371,6 +371,19 @@ void arcnet_timeout(struct net_device *dev);
#define BUS_ALIGN 1
#endif
+#ifdef CONFIG_ARCNET_COM20020_IO
+#define arcnet_inb(addr, offset) \
+ ioread8((void __iomem *)(addr) + BUS_ALIGN * offset)
+
+#define arcnet_outb(value, addr, offset) \
+ iowrite8(value, (void __iomem *)addr + BUS_ALIGN * offset)
+
+#define arcnet_insb(addr, offset, buffer, count) \
+ ioread8_rep((void __iomem *)addr + BUS_ALIGN * offset, buffer, count)
+
+#define arcnet_outsb(addr, offset, buffer, count) \
+ iowrite8_rep((void __iomem *)addr + BUS_ALIGN * offset, buffer, count)
+#else
/* addr and offset allow register like names to define the actual IO address.
* A configuration option multiplies the offset for alignment.
*/
@@ -388,6 +401,7 @@ void arcnet_timeout(struct net_device *dev);
readb((addr) + (offset))
#define arcnet_writeb(value, addr, offset) \
writeb(value, (addr) + (offset))
+#endif
#endif /* __KERNEL__ */
#endif /* _LINUX_ARCDEVICE_H */
diff --git a/drivers/net/arcnet/com20020-io.c b/drivers/net/arcnet/com20020-io.c
new file mode 100644
index 000000000000..fce458242193
--- /dev/null
+++ b/drivers/net/arcnet/com20020-io.c
@@ -0,0 +1,287 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Linux ARCnet driver for com 20020.
+ *
+ * datasheet:
+ * http://ww1.microchip.com/downloads/en/DeviceDoc/200223vrevc.pdf
+ * http://ww1.microchip.com/downloads/en/DeviceDoc/20020.pdf
+ *
+ * Supported chip version:
+ * - com20020
+ * - com20022
+ * - com20022I-3v3
+ */
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/platform_device.h>
+#include <linux/netdevice.h>
+#include <linux/of_address.h>
+#include <linux/of_gpio.h>
+#include <linux/sizes.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/delay.h>
+#include "arcdevice.h"
+#include "com20020.h"
+
+/* Reset (5 * xTalFreq), minimal com20020 xTal is 10Mhz */
+#define RESET_DELAY 500
+
+enum com20020_xtal_freq {
+ freq_10Mhz = 10,
+ freq_20Mhz = 20,
+};
+
+enum com20020_arcnet_speed {
+ arc_speed_10M_bps = 10000000,
+ arc_speed_5M_bps = 5000000,
+ arc_speed_2M50_bps = 2500000,
+ arc_speed_1M25_bps = 1250000,
+ arc_speed_625K_bps = 625000,
+ arc_speed_312K5_bps = 312500,
+ arc_speed_156K25_bps = 156250,
+};
+
+enum com20020_timeout {
+ arc_timeout_328us = 328000,
+ arc_timeout_164us = 164000,
+ arc_timeout_82us = 82000,
+ arc_timeout_20u5s = 20500,
+};
+
+static int setup_clock(int *clockp, int *clockm, int xtal, int arcnet_speed)
+{
+ int pll_factor, req_clock_frq = 20;
+
+ switch (arcnet_speed) {
+ case arc_speed_10M_bps:
+ req_clock_frq = 80;
+ *clockp = 0;
+ break;
+ case arc_speed_5M_bps:
+ req_clock_frq = 40;
+ *clockp = 0;
+ break;
+ case arc_speed_2M50_bps:
+ *clockp = 0;
+ break;
+ case arc_speed_1M25_bps:
+ *clockp = 1;
+ break;
+ case arc_speed_625K_bps:
+ *clockp = 2;
+ break;
+ case arc_speed_312K5_bps:
+ *clockp = 3;
+ break;
+ case arc_speed_156K25_bps:
+ *clockp = 4;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (xtal != freq_10Mhz && xtal != freq_20Mhz)
+ return -EINVAL;
+
+ pll_factor = (unsigned int)req_clock_frq / xtal;
+
+ switch (pll_factor) {
+ case 1:
+ *clockm = 0;
+ break;
+ case 2:
+ *clockm = 1;
+ break;
+ case 4:
+ *clockm = 3;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int setup_timeout(int *timeout)
+{
+ switch (*timeout) {
+ case arc_timeout_328us:
+ *timeout = 0;
+ break;
+ case arc_timeout_164us:
+ *timeout = 1;
+ break;
+ case arc_timeout_82us:
+ *timeout = 2;
+ break;
+ case arc_timeout_20u5s:
+ *timeout = 3;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int com20020_probe(struct platform_device *pdev)
+{
+ struct device_node *np;
+ struct net_device *dev;
+ struct arcnet_local *lp;
+ struct resource res, *iores;
+ int ret, phy_reset;
+ u32 timeout, xtal, arc_speed;
+ int clockp, clockm;
+ void __iomem *ioaddr;
+ bool backplane = false;
+
+ np = pdev->dev.of_node;
+
+ iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ ret = of_address_to_resource(np, 0, &res);
+ if (ret)
+ return ret;
+
+ ret = of_property_read_u32(np, "timeout-ns", &timeout);
+ if (ret) {
+ dev_err(&pdev->dev, "timeout is required param");
+ return ret;
+ }
+
+ ret = of_property_read_u32(np, "smsc,xtal-mhz", &xtal);
+ if (ret) {
+ dev_err(&pdev->dev, "xtal-mhz is required param");
+ return ret;
+ }
+
+ ret = of_property_read_u32(np, "bus-speed-bps", &arc_speed);
+ if (ret) {
+ dev_err(&pdev->dev, "Bus speed is required param");
+ return ret;
+ }
+
+ if (of_property_read_bool(np, "smsc,backplane-enabled"))
+ backplane = true;
+
+ phy_reset = of_get_named_gpio(np, "reset-gpios", 0);
+ if (!gpio_is_valid(phy_reset)) {
+ dev_err(&pdev->dev, "reset gpio not valid");
+ return phy_reset;
+ }
+
+ ret = devm_gpio_request_one(&pdev->dev, phy_reset, GPIOF_OUT_INIT_LOW,
+ "arcnet-reset");
+ if (ret) {
+ dev_err(&pdev->dev, "failed to get phy reset gpio: %d\n", ret);
+ return ret;
+ }
+
+ dev = alloc_arcdev(NULL);
+ dev->netdev_ops = &com20020_netdev_ops;
+ lp = netdev_priv(dev);
+
+ lp->card_flags = ARC_CAN_10MBIT;
+
+ /* Will be set by userspace during if setup */
+ dev->dev_addr[0] = 0;
+
+ if (!devm_request_mem_region(&pdev->dev, res.start, resource_size(&res),
+ lp->card_name))
+ return -EBUSY;
+
+ ioaddr = devm_ioremap(&pdev->dev, iores->start, resource_size(iores));
+ if (!ioaddr) {
+ dev_err(&pdev->dev, "ioremap fallied\n");
+ return -ENOMEM;
+ }
+
+ gpio_set_value_cansleep(phy_reset, 0);
+ ndelay(RESET_DELAY);
+ gpio_set_value_cansleep(phy_reset, 1);
+
+ /* ARCNET controller needs this access to detect bustype */
+ arcnet_outb(0x00, ioaddr, COM20020_REG_W_COMMAND);
+ arcnet_inb(ioaddr, COM20020_REG_R_DIAGSTAT);
+
+ dev->base_addr = (unsigned long)ioaddr;
+
+ dev->irq = of_get_named_gpio(np, "interrupts", 0);
+ if (dev->irq == -EPROBE_DEFER) {
+ return dev->irq;
+ } else if (!gpio_is_valid(dev->irq)) {
+ dev_err(&pdev->dev, "irq-gpios not valid !");
+ return -EIO;
+ }
+ dev->irq = gpio_to_irq(dev->irq);
+
+ ret = setup_clock(&clockp, &clockm, xtal, arc_speed);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "Impossible use oscillator:%dMhz and arcnet bus speed:%dKbps",
+ xtal, arc_speed / 1000);
+ return ret;
+ }
+
+ ret = setup_timeout(&timeout);
+ if (ret) {
+ dev_err(&pdev->dev, "Timeout:%d is not valid value", timeout);
+ return ret;
+ }
+
+ lp->backplane = (int)backplane;
+ lp->timeout = timeout;
+ lp->clockm = clockm;
+ lp->clockp = clockp;
+ lp->hw.owner = THIS_MODULE;
+
+ if (arcnet_inb(ioaddr, COM20020_REG_R_STATUS) == 0xFF) {
+ ret = -EIO;
+ goto err_release_mem;
+ }
+
+ if (com20020_check(dev)) {
+ ret = -EIO;
+ goto err_release_mem;
+ }
+
+ ret = com20020_found(dev, IRQF_TRIGGER_FALLING);
+ if (ret)
+ goto err_release_mem;
+
+ dev_dbg(&pdev->dev, "probe Done\n");
+ return 0;
+
+err_release_mem:
+ devm_iounmap(&pdev->dev, (void __iomem *)ioaddr);
+ devm_release_mem_region(&pdev->dev, res.start, resource_size(&res));
+ dev_err(&pdev->dev, "probe failed!\n");
+ return ret;
+}
+
+static const struct of_device_id of_com20020_match[] = {
+ { .compatible = "smsc,com20020", },
+ { },
+};
+
+MODULE_DEVICE_TABLE(of, of_com20020_match);
+
+static struct platform_driver of_com20020_driver = {
+ .driver = {
+ .name = "com20020-memory-bus",
+ .of_match_table = of_com20020_match,
+ },
+ .probe = com20020_probe,
+};
+
+static int com20020_init(void)
+{
+ return platform_driver_register(&of_com20020_driver);
+}
+late_initcall(com20020_init);
+
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/arcnet/com20020.c b/drivers/net/arcnet/com20020.c
index 78043a9c5981..2fd00d2dd6bf 100644
--- a/drivers/net/arcnet/com20020.c
+++ b/drivers/net/arcnet/com20020.c
@@ -43,7 +43,7 @@
#include "com20020.h"
static const char * const clockrates[] = {
- "XXXXXXX", "XXXXXXXX", "XXXXXX", "2.5 Mb/s",
+ "10 Mb/s", "XXXXXXXX", "XXXXXX", "2.5 Mb/s",
"1.25Mb/s", "625 Kb/s", "312.5 Kb/s", "156.25 Kb/s",
"Reserved", "Reserved", "Reserved"
};
@@ -393,7 +393,8 @@ static void com20020_set_mc_list(struct net_device *dev)
#if defined(CONFIG_ARCNET_COM20020_PCI_MODULE) || \
defined(CONFIG_ARCNET_COM20020_ISA_MODULE) || \
- defined(CONFIG_ARCNET_COM20020_CS_MODULE)
+ defined(CONFIG_ARCNET_COM20020_CS_MODULE) || \
+ defined(CONFIG_ARCNET_COM20020_IO)
EXPORT_SYMBOL(com20020_check);
EXPORT_SYMBOL(com20020_found);
EXPORT_SYMBOL(com20020_netdev_ops);
--
2.14.3