Re: [PATCH v1 06/15] drm/mediatek: add memory mode for RDMA

[Stu Hsieh]

Hi, CK:

On Wed, 2018-07-25 at 10:40 +0800, CK Hu wrote:
> Hi, Stu:
> 
> On Tue, 2018-07-24 at 16:17 +0800, Stu Hsieh wrote:
> > This patch add memory mode for RDMA
> > 
> > If use RDMA to read data from memory, it should set memory mode to RDMA
> > 
> > Signed-off-by: Stu Hsieh <stu.hsieh@xxxxxxxxxxxx>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_disp_rdma.c | 16 +++++++++++++++-
> >  1 file changed, 15 insertions(+), 1 deletion(-)
> > 
> 
> [...]
> 
> >  static inline struct mtk_disp_rdma *comp_to_rdma(struct mtk_ddp_comp *comp)
> > @@ -111,7 +116,8 @@ static void mtk_rdma_start(struct mtk_ddp_comp *comp)
> >  
> >  static void mtk_rdma_stop(struct mtk_ddp_comp *comp)
> >  {
> > -	rdma_update_bits(comp, DISP_REG_RDMA_GLOBAL_CON, RDMA_ENGINE_EN, 0);
> > +	writel(RDMA_SOFT_RESET, comp->regs + DISP_REG_RDMA_GLOBAL_CON);
> > +	writel(0, comp->regs + DISP_REG_RDMA_GLOBAL_CON);
> 
> Without reset, what happen to dram mode? Why direct link mode need not
> this reset?
> 

There is nothing to happen, I would remove it.

> >  }
> >  
> >  static void mtk_rdma_config(struct mtk_ddp_comp *comp, unsigned int width,
> > @@ -121,10 +127,18 @@ static void mtk_rdma_config(struct mtk_ddp_comp *comp, unsigned int width,
> >  	unsigned int threshold;
> >  	unsigned int reg;
> >  	struct mtk_disp_rdma *rdma = comp_to_rdma(comp);
> > +	bool *rdma_memory_mode = comp->comp_mode;
> >  
> >  	rdma_update_bits(comp, DISP_REG_RDMA_SIZE_CON_0, 0xfff, width);
> >  	rdma_update_bits(comp, DISP_REG_RDMA_SIZE_CON_1, 0xfffff, height);
> >  
> > +	if (*rdma_memory_mode == true) {
> > +		rdma_update_bits(comp, DISP_REG_RDMA_SIZE_CON_0, 0xff0000,
> > +				 MATRIX_INT_MTX_SEL_DEFAULT);
> > +		rdma_update_bits(comp, DISP_REG_RDMA_GLOBAL_CON,
> > +				 RDMA_MODE_MEMORY, RDMA_MODE_MEMORY);
> > +	}
> > +
> 
> I would like this to be a kind of 'layer' config. In some SoC, one layer
> of OVL could switch to direct link input or dram input. So I think it's
> better to move this setting into some layer interface.
> 
> Regards,
> CK
> 

If move it to layer_config, RDMA would not trigger interrupt.
In the future, when cmdq patch upstream and accepted, this part can move
to layer_config. 

Regard,
Stu

> >  	/*
> >  	 * Enable FIFO underflow since DSI and DPI can't be blocked.
> >  	 * Keep the FIFO pseudo size reset default of 8 KiB. Set the
> 
>