Re: [PATCH v1 1/1] Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990

[Marcel Holtmann]

Hi Balakrishna,

> This patch enables power off support for hci down and power on support
> for hci up. As wcn3990 power sources are ignited by regulators, we will
> turn off them during hci down, i.e. an complete power off of wcn3990.
> So while hci up, we will call vendor specific open/close and setup which
> will turn on the regulators, requests BT chip version and download the
> firmware.
> 
> Signed-off-by: Balakrishna Godavarthi <bgodavar@xxxxxxxxxxxxxx>
> ---
> drivers/bluetooth/hci_qca.c | 34 ++++++++++++++++++++++++++++++++++
> 1 file changed, 34 insertions(+)
> 
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index e182f6019f68..98d33c6b8909 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
> @@ -595,6 +595,9 @@ static int qca_close(struct hci_uart *hu)
> 	struct qca_serdev *qcadev;
> 	struct qca_data *qca = hu->priv;
> 
> +	if (!qca)
> +		return 0;
> +
> 	BT_DBG("hu %p qca close", hu);
> 
> 	serial_clock_vote(HCI_IBS_VOTE_STATS_UPDATE, hu);
> @@ -1098,6 +1101,32 @@ static int qca_set_speed(struct hci_uart *hu, enum qca_speed_type speed_type)
> 	return 0;
> }
> 
> +static int hci_uart_open(struct hci_dev *hdev)
> +{
> +	struct hci_uart *hu = hci_get_drvdata(hdev);
> +
> +	BT_DBG("%s %p", hdev->name, hdev);
> +	set_bit(HCI_UART_PROTO_READY, &hu->flags);
> +
> +	return qca_open(hu);
> +}
> +
> +static int hci_uart_close(struct hci_dev *hdev)
> +{
> +	struct hci_uart *hu = hci_get_drvdata(hdev);
> +
> +	BT_DBG("%s %p", hdev->name, hdev);
> +
> +	/* After this step, we should not allow Tx and Rx work
> +	 * function to execute. As we are freeing qca tx and rx
> +	 * buffers which may cause kernel crash.
> +	 */
> +	clear_bit(HCI_UART_PROTO_READY, &hu->flags);
> +	qca_close(hu);
> +
> +	return 0;
> +}
> +
> static int qca_wcn3990_init(struct hci_uart *hu)
> {
> 	struct hci_dev *hdev = hu->hdev;
> @@ -1154,6 +1183,11 @@ static int qca_setup(struct hci_uart *hu)
> 
> 	if (qcadev->btsoc_type == QCA_WCN3990) {
> 		bt_dev_info(hdev, "setting up wcn3990");
> +
> +		hdev->open  = hci_uart_open;
> +		hdev->close = hci_uart_close;
> +		set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
> +

I do not get this change and I am also against it. Once hdev->open and hdev->close are assigned, donât re-assign them. You called hci_register_dev and you are not changing the basic transport open/close functions after that. If you need some vendor specific things to open and close the transport, then do it properly.

When I posted the btuart.c serdev driver, it would be a lot easier to add vendor specific things then to hci_serdev.c which is still kinda hacked onto a line discipline driver.

Regards

Marcel