Re: [PATCH v4 07/10] dt-bindings: phy: add binding for Allwinner USB3 PHY

[Icenowy Zheng]

å 2018-10-18åç 08:58 -0500ïRob Herringåéï
> On Sat, Oct 13, 2018 at 9:42 PM Icenowy Zheng <icenowy@xxxxxxx>
> wrote:
> > 
> > å 2018-10-05äç 15:58 -0500ïRob Herringåéï
> > > On Thu, Oct 04, 2018 at 08:28:52PM +0800, Icenowy Zheng wrote:
> > > > The new Allwinner H6 SoC contains a USB3 PHY that is wired to
> > > > the
> > > > external USB3 pins of the SoC.
> > > > 
> > > > Add a device tree binding for the PHY.
> > > > 
> > > > Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
> > > > Reviewed-by: Chen-Yu Tsai <wens@xxxxxxxx>
> > > > ---
> > > > Changes in v4:
> > > > - Changed Vbus regulator property to vbus-supply.
> > > > 
> > > > Changes in v3:
> > > > - Added Chen-Yu's Review tag.
> > > > 
> > > > No changes in v2, v1.
> > > > 
> > > >  .../bindings/phy/sun50i-usb3-phy.txt          | 23
> > > > +++++++++++++++++++
> > > >  1 file changed, 23 insertions(+)
> > > >  create mode 100644
> > > > Documentation/devicetree/bindings/phy/sun50i-
> > > > usb3-phy.txt
> > > > 
> > > > diff --git a/Documentation/devicetree/bindings/phy/sun50i-usb3-
> > > > phy.txt b/Documentation/devicetree/bindings/phy/sun50i-usb3-
> > > > phy.txt
> > > > new file mode 100644
> > > > index 000000000000..9f49c6b8c7e7
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/phy/sun50i-usb3-phy.txt
> > > > @@ -0,0 +1,23 @@
> > > > +Allwinner sun50i USB3 PHY
> > > > +-----------------------
> > > > +
> > > > +Required properties:
> > > > +- compatible : should be one of
> > > > +  * allwinner,sun60i-h6-usb3-phy
> > > > +- reg : a list of offset + length pairs
> > > > +- #phy-cells : from the generic phy bindings, must be 0
> > > > +- clocks : phandle + clock specifier for the phy clock
> > > > +- resets : phandle + reset specifier for the phy reset
> > > > +
> > > > +Optional Properties:
> > > > +- vbus-supply : a phandle to a regulator that provides power
> > > > to
> > > > VBUS.
> > > 
> > > This belongs in a connector node as it is part of the connector
> > > unless
> > > the phy physically needs Vbus for power.
> > > 
> > > But others have done this, so all the phys can just be wrong...
> > 
> > How should we reference the connector?
> > 
> > Via OF graph or simply a property in PHY node?
> 
> The connector is either a child of the controller or an OF graph from
> the controller to the connector. The phy driver needs the controller
> node and then it can walk the tree or graph to get the connector
> node.

By reading the binding, it says the connector should be a child of the
"interface controller", not the USB controller. In this case I think
the interface controller is the PHY rather than the USB controller.

In addition, the connector is a passive component, and power management
should be done by the "interface controller", either directly by the
PHY or make a dummy interface controller driver that only controls the
Vbus.

> 
> Rob
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel