Re: [PATCH v6 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC

[Manivannan Sadhasivam]

On Tue, Nov 13, 2018 at 11:07:07AM +0100, Parthiban Nallathambi wrote:
> From: Saravanan Sekar <sravanhome@xxxxxxxxx>
> 
> Add pinctrl and pio bindings for Actions Semi S700 SoC.
> 
> Signed-off-by: Parthiban Nallathambi <pn@xxxxxxx>
> Signed-off-by: Saravanan Sekar <sravanhome@xxxxxxxxx>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> ---
>  .../bindings/pinctrl/actions,s700-pinctrl.txt | 170 ++++++++++++++++++
>  1 file changed, 170 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt
> new file mode 100644
> index 000000000000..c72c09c38537
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt
> @@ -0,0 +1,170 @@
> +Actions Semi S700 Pin Controller
> +
> +This binding describes the pin controller found in the S700 SoC.
> +
> +Required Properties:
> +
> +- compatible:   Should be "actions,s700-pinctrl"
> +- reg:          Should contain the register base address and size of
> +		the pin controller.
> +- clocks:       phandle of the clock feeding the pin controller
> +- gpio-controller: Marks the device node as a GPIO controller.
> +- gpio-ranges: Specifies the mapping between gpio controller and
> +               pin-controller pins.
> +- #gpio-cells: Should be two. The first cell is the gpio pin number
> +		and the second cell is used for optional parameters.
> +- interrupt-controller: Marks the device node as an interrupt controller.
> +- #interrupt-cells: Specifies the number of cells needed to encode an
> +		interrupt.  Shall be set to 2.  The first cell
> +		defines the interrupt number, the second encodes
> +		the trigger flags described in
> +		bindings/interrupt-controller/interrupts.txt
> +- interrupts: The interrupt outputs from the controller. There is one GPIO
> +              interrupt per GPIO bank. The number of interrupts listed depends
> +              on the number of GPIO banks on the SoC. The interrupts must be
> +              ordered by bank, starting with bank 0.
> +
> +Please refer to pinctrl-bindings.txt in this directory for details of the
> +common pinctrl bindings used by client devices, including the meaning of the
> +phrase "pin configuration node".
> +
> +The pin configuration nodes act as a container for an arbitrary number of
> +subnodes. Each of these subnodes represents some desired configuration for a
> +pin, a group, or a list of pins or groups. This configuration can include the
> +mux function to select on those group(s), and various pin configuration
> +parameters, such as pull-up, drive strength, etc.
> +
> +PIN CONFIGURATION NODES:
> +
> +The name of each subnode is not important; all subnodes should be enumerated
> +and processed purely based on their content.
> +
> +Each subnode only affects those parameters that are explicitly listed. In
> +other words, a subnode that lists a mux function but no pin configuration
> +parameters implies no information about any pin configuration parameters.
> +Similarly, a pin subnode that describes a pullup parameter implies no
> +information about e.g. the mux function.
> +
> +Pinmux functions are available only for the pin groups while pinconf
> +parameters are available for both pin groups and individual pins.
> +
> +The following generic properties as defined in pinctrl-bindings.txt are valid
> +to specify in a pin configuration subnode:
> +
> +Required Properties:
> +
> +- pins:		An array of strings, each string containing the name of a pin.
> +		These pins are used for selecting the pull control and schmitt
> +		trigger parameters. The following are the list of pins
> +		available:
> +
> +		eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer,
> +		eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk,
> +		eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0,
> +		i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1,
> +		pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2,
> +		ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp,
> +		lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap,
> +		lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp,
> +		lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18,
> +		lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn,
> +		dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2,
> +		sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk,
> +		sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx,
> +		uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx,
> +		uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk,
> +		i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1,
> +		csi_cn, csi_cp, csi_dn2, csi_dp2, csi_dn3, csi_dp3,
> +		sensor0_pclk, sensor0_ckout, dnand_d0, dnand_d1, dnand_d2,
> +		dnand_d3, dnand_d4, dnand_d5, dnand_d6, dnand_d7, dnand_wrb,
> +		dnand_rdb, dnand_rdbn, dnand_dqs, dnand_dqsn, dnand_rb0,
> +		dnand_ale, dnand_cle, dnand_ceb0, dnand_ceb1, dnand_ceb2,
> +		dnand_ceb3, porb, clko_25m, bsel, pkg0, pkg1, pkg2, pkg3
> +
> +- groups:       An array of strings, each string containing the name of a pin
> +                group. These pin groups are used for selecting the pinmux
> +                functions.
> +		rgmii_txd23_mfp, rgmii_rxd2_mfp, rgmii_rxd3_mfp, lcd0_d18_mfp,
> +		rgmii_txd01_mfp, rgmii_txd0_mfp, rgmii_txd1_mfp, rgmii_txen_mfp,
> +		rgmii_rxen_mfp, rgmii_rxd1_mfp, rgmii_rxd0_mfp, rgmii_ref_clk_mfp,
> +		i2s_d0_mfp, i2s_pcm1_mfp, i2s0_pcm0_mfp, i2s1_pcm0_mfp,
> +		i2s_d1_mfp, ks_in2_mfp, ks_in1_mfp, ks_in0_mfp, ks_in3_mfp,
> +		ks_out0_mfp, ks_out1_mfp, ks_out2_mfp, lvds_o_pn_mfp, dsi_dn0_mfp,
> +		dsi_dp2_mfp, lcd0_d2_mfp, dsi_dp3_mfp, dsi_dn3_mfp, dsi_dp0_mfp,
> +		lvds_ee_pn_mfp, uart2_rx_tx_mfp, spi0_i2c_pcm_mfp, dsi_dnp1_cp_d2_mfp,
> +		dsi_dnp1_cp_d17_mfp, lvds_e_pn_mfp, dsi_dn2_mfp, uart2_rtsb_mfp,
> +		uart2_ctsb_mfp, uart3_rtsb_mfp, uart3_ctsb_mfp, sd0_d0_mfp, sd0_d1_mfp,
> +		sd0_d2_d3_mfp, sd1_d0_d3_mfp, sd0_cmd_mfp, sd0_clk_mfp, sd1_cmd_mfp,
> +		uart0_rx_mfp, clko_25m_mfp, csi_cn_cp_mfp, sens0_ckout_mfp, uart0_tx_mfp,
> +		i2c0_mfp, csi_dn_dp_mfp, sen0_pclk_mfp, pcm1_in_mfp, pcm1_clk_mfp,
> +		pcm1_sync_mfp, pcm1_out_mfp, dnand_data_wr_mfp, dnand_acle_ce0_mfp,
> +		nand_ceb2_mfp, nand_ceb3_mfp
> +
> +		These pin groups are used for selecting the drive strength
> +		parameters.
> +
> +		sirq_drv, rgmii_txd23_drv, rgmii_rxd23_drv, rgmii_txd01_txen_drv,
> +		rgmii_rxer_drv, rgmii_crs_drv, rgmii_rxd10_drv, rgmii_ref_clk_drv,
> +		smi_mdc_mdio_drv, i2s_d0_drv, i2s_bclk0_drv, i2s3_drv, i2s13_drv,
> +		pcm1_drv, ks_in_drv, ks_out_drv, lvds_all_drv, lcd_d18_d2_drv,
> +		dsi_all_drv, sd0_d0_d3_drv, sd0_cmd_drv, sd0_clk_drv, spi0_all_drv,
> +		uart0_rx_drv, uart0_tx_drv, uart2_all_drv, i2c0_all_drv, i2c12_all_drv,
> +		sens0_pclk_drv, sens0_ckout_drv, uart3_all_drv
> +
> +- function:	An array of strings, each string containing the name of the
> +		pinmux functions. These functions can only be selected by
> +		the corresponding pin groups. The following are the list of
> +		pinmux functions available:
> +
> +		nor, eth_rgmii, eth_sgmii, spi0, spi1, spi2, spi3, seNs0, sens1,
> +		uart0, uart1, uart2, uart3, uart4, uart5, uart6, i2s0, i2s1,
> +		pcm1, pcm0, ks, jtag, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, p0,
> +		sd0, sd1, sd2, i2c0, i2c1, i2c2, i2c3, dsi, lvds, usb30,
> +		clko_25m, mipi_csi, nand, spdif, sirq0, sirq1, sirq2, bt, lcd0
> +
> +Optional Properties:
> +
> +- bias-pull-down: No arguments. The specified pins should be configured as
> +		pull down.
> +- bias-pull-up:   No arguments. The specified pins should be configured as
> +		pull up.
> +- input-schmitt-enable: No arguments: Enable schmitt trigger for the specified
> +		pins
> +- input-schmitt-disable: No arguments: Disable schmitt trigger for the specified
> +		pins
> +- drive-strength: Integer. Selects the drive strength for the specified
> +		pins in mA.
> +		Valid values are:
> +		<2>
> +		<4>
> +		<8>
> +		<12>
> +
> +Example:
> +
> +	pinctrl: pinctrl@e01b0000 {
> +		compatible = "actions,s700-pinctrl";
> +		reg = <0x0 0xe01b0000 0x0 0x1000>;
> +		clocks = <&cmu CLK_GPIO>;
> +		gpio-controller;
> +		gpio-ranges = <&pinctrl 0 0 136>;
> +		#gpio-cells = <2>;
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +                interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
> +                             <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
> +                             <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
> +                             <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
> +                             <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,

Nitpick: Cells should be terminated with a semicolon. This was mentioned
in my previous review as well.

Regards,
Mani

> +
> +		uart3-default: uart3-default {
> +			pinmux {
> +				groups = "uart3_rtsb_mfp", "uart3_ctsb_mfp";
> +				function = "uart3";
> +			};
> +			pinconf {
> +				groups = "uart3_all_drv";
> +				drive-strength = <2>;
> +			};
> +		};
> +	};
> -- 
> 2.17.2
>