Re: [PATCH v5 3/9] spi: Add a driver for the Freescale/NXP QuadSPI controller

[Schrempf Frieder]

On 15.11.18 07:22, Yogesh Narayan Gaur wrote:
> Hi Frieder,
> 
> With below patch on top of your v5, Read/Write/Erase on CS1 is working fine for me.

Ok, are you sure, that AHB read is working too with this patch?
You are removing the memmap_phy offset from SFAR and the SFXXAD register 
values.

I can understand that selection of the CS and IP commands will work like 
this, but I can't understand how AHB read should work without the base 
address of the mapped memory.

I'm afraid I still don't fully understand the background of these 
things, but still thank you for testing.

> 
> I have tested with JFFS2 mounting and booting also for both CS0 and CS1.
> 
> diff --git a/drivers/spi/spi-fsl-qspi.c b/drivers/spi/spi-fsl-qspi.c
> index ce45e8e..4467983 100644
> --- a/drivers/spi/spi-fsl-qspi.c
> +++ b/drivers/spi/spi-fsl-qspi.c
> @@ -490,28 +490,10 @@ static void fsl_qspi_select_mem(struct fsl_qspi *q, struct spi_device *spi)
>   {
>          unsigned long rate = spi->max_speed_hz;
>          int ret, i;
> -       u32 map_addr;
> 
>          if (q->selected == spi->chip_select)
>                  return;
> 
> -       /*
> -        * In HW there can be a maximum of four chips on two buses with
> -        * two chip selects on each bus. We use four chip selects in SW
> -        * to differentiate between the four chips.
> -        * We use the SFA1AD, SFA2AD, SFB1AD, SFB2AD registers to select
> -        * the chip we want to access.
> -        */
> -       for (i = 0; i < 4; i++) {
> -               if (i < spi->chip_select)
> -                       map_addr = q->memmap_phy;
> -               else
> -                       map_addr = q->memmap_phy +
> -                                  2 * q->devtype_data->ahb_buf_size;
> -
> -               qspi_writel(q, map_addr, q->iobase + QUADSPI_SFA1AD + (i * 4));
> -       }
> -
>          if (needs_4x_clock(q))
>                  rate *= 4;
> 
> @@ -534,7 +516,9 @@ static void fsl_qspi_select_mem(struct fsl_qspi *q, struct spi_device *spi)
> 
>   static void fsl_qspi_read_ahb(struct fsl_qspi *q, const struct spi_mem_op *op)
>   {
> -       memcpy_fromio(op->data.buf.in, q->ahb_addr, op->data.nbytes);
> +       memcpy_fromio(op->data.buf.in,
> +                     q->ahb_addr + q->selected * q->devtype_data->ahb_buf_size,
> +                     op->data.nbytes);
>   }
> 
>   static void fsl_qspi_fill_txfifo(struct fsl_qspi *q,
> @@ -634,7 +618,9 @@ static int fsl_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
> 
>          fsl_qspi_select_mem(q, mem->spi);
> 
> -       qspi_writel(q, q->memmap_phy, base + QUADSPI_SFAR);
> +       qspi_writel(q,
> +                   q->selected * q->devtype_data->ahb_buf_size,
> +                   base + QUADSPI_SFAR);
> 
>          qspi_writel(q, qspi_readl(q, base + QUADSPI_MCR) |
>                      QUADSPI_MCR_CLR_RXF_MASK | QUADSPI_MCR_CLR_TXF_MASK,
> @@ -733,6 +719,19 @@ static int fsl_qspi_default_setup(struct fsl_qspi *q)
>                      QUADSPI_BUF3CR_ADATSZ(q->devtype_data->ahb_buf_size / 8),
>                      base + QUADSPI_BUF3CR);
> 
> +       /*
> +        * In HW there can be a maximum of four chips on two buses with
> +        * two chip selects on each bus. We use four chip selects in SW
> +        * to differentiate between the four chips.
> +        * We use the SFA1AD, SFA2AD, SFB1AD, SFB2AD registers to select
> +        * the chip we want to access.
> +        */
> +
> +       qspi_writel(q, q->devtype_data->ahb_buf_size, base + QUADSPI_SFA1AD);
> +       qspi_writel(q, q->devtype_data->ahb_buf_size * 2 , base + QUADSPI_SFA2AD);
> +       qspi_writel(q, q->devtype_data->ahb_buf_size * 3 , base + QUADSPI_SFB1AD);
> +       qspi_writel(q, q->devtype_data->ahb_buf_size * 4 , base + QUADSPI_SFB2AD);
> +
>          q->selected = -1;
> 
> --
> Regards
> Yogesh Gaur
> 
> [..]
>