Re: [PATCH 2/5] i2c: mediatek: remove useless code and replace definitions

[Qii Wang]

On Tue, 2018-12-11 at 21:20 +0100, Wolfram Sang wrote:
> On Mon, Dec 03, 2018 at 09:32:51PM +0800, qii.wang@xxxxxxxxxxxx wrote:
> > From: qii wang <qii.wang@xxxxxxxxxxxx>
> > 
> > Completion_done is useless when we don't use its return value,
> > so we remove it. Different speeds have been defined by macros,
> > so we use macros definitions.
> 
> Those are two seperate patches, or?
> 

These two changes are relatively small, but it seems better to be
divided into two seperate patches.

> > 
> > Signed-off-by: qii wang <qii.wang@xxxxxxxxxxxx>
> > ---
> >  drivers/i2c/busses/i2c-mt65xx.c |    6 ++----
> >  1 file changed, 2 insertions(+), 4 deletions(-)
> > 
> > diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
> > index a74ef76..660de1e 100644
> > --- a/drivers/i2c/busses/i2c-mt65xx.c
> > +++ b/drivers/i2c/busses/i2c-mt65xx.c
> > @@ -456,7 +456,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
> >  
> >  	control_reg = readw(i2c->base + OFFSET_CONTROL) &
> >  			~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS);
> > -	if ((i2c->speed_hz > 400000) || (left_num >= 1))
> > +	if ((i2c->speed_hz > MAX_FS_MODE_SPEED) || (left_num >= 1))
> >  		control_reg |= I2C_CONTROL_RS;
> >  
> >  	if (i2c->op == I2C_MASTER_WRRD)
> > @@ -465,7 +465,7 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
> >  	writew(control_reg, i2c->base + OFFSET_CONTROL);
> >  
> >  	/* set start condition */
> > -	if (i2c->speed_hz <= 100000)
> > +	if (i2c->speed_hz <= I2C_DEFAULT_SPEED)
> >  		writew(I2C_ST_START_CON, i2c->base + OFFSET_EXT_CONF);
> >  	else
> >  		writew(I2C_FS_START_CON, i2c->base + OFFSET_EXT_CONF);
> > @@ -642,8 +642,6 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
> >  		return -ETIMEDOUT;
> >  	}
> >  
> > -	completion_done(&i2c->msg_complete);
> > -
> >  	if (i2c->irq_stat & (I2C_HS_NACKERR | I2C_ACKERR)) {
> >  		dev_dbg(i2c->dev, "addr: %x, transfer ACK error\n", msgs->addr);
> >  		mtk_i2c_init_hw(i2c);
> > -- 
> > 1.7.9.5
> >