[PATCH V1 10/11] mmc: tegra: fix CQE resume sequence

[Sowjanya Komatineni]

Tegra CQHCI/SDHCI design prevents write access to SDHCI block size
register when CQE is enabled and unhalted.

CQHCI driver enabled CQE prior to invoking sdhci_cqe_enable which
violates this Tegra specific host requirement.

This patch fixes this by configuring sdhci block registers prior
to CQE unhalt.

Signed-off-by: Sowjanya Komatineni <skomatineni@xxxxxxxxxx>
---
 drivers/mmc/host/sdhci-tegra.c | 71 ++++++++++++++++++++++++++++++++++++------
 1 file changed, 62 insertions(+), 9 deletions(-)

diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
index 2b63626dc2fa..7063cfcdc590 100644
--- a/drivers/mmc/host/sdhci-tegra.c
+++ b/drivers/mmc/host/sdhci-tegra.c
@@ -1126,23 +1126,75 @@ static void tegra_sdhci_voltage_switch(struct sdhci_host *host)
 		tegra_host->pad_calib_required = true;
 }
 
+static void tegra_cqhci_writel(struct cqhci_host *cq_host, u32 val, int reg)
+{
+	struct mmc_host *mmc = cq_host->mmc;
+	u8 ctrl;
+	ktime_t timeout;
+	bool timed_out;
+
+	/*
+	 * During CQE resume/unhalt, CQHCI driver unhalts CQE prior to
+	 * cqhci_host_ops enable where SDHCI DMA and BLOCK_SIZE registers need
+	 * to be re-configured.
+	 * Tegra CQHCI/SDHCI prevents write access to block size register when
+	 * CQE is unhalted. So handling CQE resume sequence here to configure
+	 * SDHCI block registers prior to exiting CQE halt state.
+	 */
+	if (reg == CQHCI_CTL && !(val & CQHCI_HALT) &&
+	    cqhci_readl(cq_host, CQHCI_CTL) & CQHCI_HALT) {
+		sdhci_cqe_enable(mmc);
+		writel(val, cq_host->mmio + reg);
+		timeout = ktime_add_us(ktime_get(), 50);
+		while (1) {
+			timed_out = ktime_compare(ktime_get(), timeout) > 0;
+			ctrl = cqhci_readl(cq_host, CQHCI_CTL);
+			if (!(ctrl & CQHCI_HALT) || timed_out)
+				break;
+		}
+		/*
+		 * CQE usually resumes very quick, but incase if Tegra CQE
+		 * doesn't resume retry unhalt.
+		 */
+		if (timed_out)
+			writel(val, cq_host->mmio + reg);
+	} else {
+		writel(val, cq_host->mmio + reg);
+	}
+}
+
 static void sdhci_tegra_cqe_enable(struct mmc_host *mmc)
 {
 	struct cqhci_host *cq_host = mmc->cqe_private;
-	u32 cqcfg = 0;
+	u32 val;
 
 	/*
-	 * Tegra SDMMC Controller design prevents write access to BLOCK_COUNT
-	 * registers when CQE is enabled.
+	 * Tegra CQHCI/SDMMC design prevents write access to sdhci block size
+	 * register when CQE is enabled and unhalted.
+	 * CQHCI driver enables CQE prior to activation, so disable CQE before
+	 * programming block size in sdhci controller and enable it back.
 	 */
-	cqcfg = cqhci_readl(cq_host, CQHCI_CFG);
-	if (cqcfg & CQHCI_ENABLE)
-		cqhci_writel(cq_host, (cqcfg & ~CQHCI_ENABLE), CQHCI_CFG);
+	if (!cq_host->activated) {
+		val = cqhci_readl(cq_host, CQHCI_CFG);
+		if (val & CQHCI_ENABLE)
+			cqhci_writel(cq_host, (val & ~CQHCI_ENABLE),
+				     CQHCI_CFG);
+		sdhci_cqe_enable(mmc);
+		if (val & CQHCI_ENABLE)
+			cqhci_writel(cq_host, val, CQHCI_CFG);
+	}
 
-	sdhci_cqe_enable(mmc);
+	/*
+	 * CMD CRC errors are seen sometimes with some eMMC devices when status
+	 * command is sent during transfer of last data block which is the
+	 * default case as send status command block counter (CBC) is 1.
+	 * So changing send status command block counter (CBC) to 0 to allow
+	 * send status command only when the data lines are idle.
+	 */
+	val = cqhci_readl(cq_host, CQHCI_SSC1);
+	val &= ~CQHCI_SSC1_CBC_MASK;
+	cqhci_writel(cq_host, val, CQHCI_SSC1);
 
-	if (cqcfg & CQHCI_ENABLE)
-		cqhci_writel(cq_host, cqcfg, CQHCI_CFG);
 }
 
 static void sdhci_tegra_dumpregs(struct mmc_host *mmc)
@@ -1167,6 +1219,7 @@ static const struct cqhci_host_ops sdhci_tegra_cqhci_ops = {
 	.enable	= sdhci_tegra_cqe_enable,
 	.disable = sdhci_cqe_disable,
 	.dumpregs = sdhci_tegra_dumpregs,
+	.write_l    = tegra_cqhci_writel,
 };
 
 static const struct sdhci_ops tegra_sdhci_ops = {
-- 
2.7.4