Re: [PATCHv2 1/5] Documentation: dt: edac: Fix Stratix10 IRQ bindings

[Rob Herring]

On Wed, Feb 27, 2019 at 11:27:21AM -0600, thor.thayer@xxxxxxxxxxxxxxx wrote:
> From: Thor Thayer <thor.thayer@xxxxxxxxxxxxxxx>
> 
> Fix Stratix10 ECC bindings to specify only the single
> bit error. On Stratix10 double bit errors are handled
> as SErrors instead of interrupts.
> Indicate the differences between the ARM64 and ARM32
> EDAC architecture in the bindings.
> 
> Signed-off-by: Thor Thayer <thor.thayer@xxxxxxxxxxxxxxx>
> ---
> v2 No change
> ---
>  .../devicetree/bindings/edac/socfpga-eccmgr.txt    | 23 +++++++++++++++-------
>  1 file changed, 16 insertions(+), 7 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt
> index 5626560a6cfd..a0ac50e15912 100644
> --- a/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt
> +++ b/Documentation/devicetree/bindings/edac/socfpga-eccmgr.txt
> @@ -236,33 +236,42 @@ Stratix10 SoCFPGA ECC Manager
>  The Stratix10 SoC ECC Manager handles the IRQs for each peripheral
>  in a shared register similar to the Arria10. However, ECC requires
>  access to registers that can only be read from Secure Monitor with
> -SMC calls. Therefore the device tree is slightly different.
> +SMC calls. Therefore the device tree is slightly different. Note that
> +only 1 interrupt is sent because the double bit errors are treated as
> +SErrors instead of IRQ.
>  
>  Required Properties:
>  - compatible : Should be "altr,socfpga-s10-ecc-manager"
> -- interrupts : Should be single bit error interrupt, then double bit error
> -	interrupt.
> +- altr,sysgr-syscon : phandle to Stratix10 System Manager Block
> +	              containing the ECC manager registers.

Seems this was already in use, but why not just make this node a child 
of the System Manager Block and remove this phandle?

> +- interrupts : Should be single bit error interrupt.
>  - interrupt-controller : boolean indicator that ECC Manager is an interrupt controller
>  - #interrupt-cells : must be set to 2.
> +- #address-cells: must be 1
> +- #size-cells: must be 1
> +- ranges : standard definition, should translate from local addresses
>  
>  Subcomponents:
>  
>  SDRAM ECC
>  Required Properties:
>  - compatible : Should be "altr,sdram-edac-s10"
> -- interrupts : Should be single bit error interrupt, then double bit error
> -	interrupt, in this order.
> +- interrupts : Should be single bit error interrupt.
>  
>  Example:
>  
>  	eccmgr {
>  		compatible = "altr,socfpga-s10-ecc-manager";
> -		interrupts = <0 15 4>, <0 95 4>;
> +		altr,sysmgr-syscon = <&sysmgr>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		interrupts = <0 15 4>;
>  		interrupt-controller;
>  		#interrupt-cells = <2>;
> +		ranges;
>  
>  		sdramedac {
>  			compatible = "altr,sdram-edac-s10";
> -			interrupts = <16 4>, <48 4>;
> +			interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
>  		};
>  	};
> -- 
> 2.7.4
>