Re: [PATCH v5 2/5] usb: phy: Workaround for USB erratum-A005728

[Alan Stern]

On Wed, 8 May 2019, Yinbo Zhu wrote:

> From: Suresh Gupta <B42813@xxxxxxxxxxxxx>
> 
> PHY_CLK_VALID bit for UTMI PHY in USBDR does not set even
> if PHY is providing valid clock. Workaround for this
> involves resetting of PHY and check PHY_CLK_VALID bit
> multiple times. If PHY_CLK_VALID bit is still not set even
> after 5 retries, it would be safe to deaclare that PHY
> clock is not available.
> This erratum is applicable for USBDR less then ver 2.4.
> 
> Signed-off-by: Suresh Gupta <B42813@xxxxxxxxxxxxx>
> Signed-off-by: Yinbo Zhu <yinbo.zhu@xxxxxxx>
> ---
> Change in v5:
> 		remove dev_err function unnecessary parameters 
> 
>  drivers/usb/host/ehci-fsl.c |   37 ++++++++++++++++++++++++++-----------
>  drivers/usb/host/ehci-fsl.h |    3 +++
>  2 files changed, 29 insertions(+), 11 deletions(-)
> 
> diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
> index 38674b7..1634ac8 100644
> --- a/drivers/usb/host/ehci-fsl.c
> +++ b/drivers/usb/host/ehci-fsl.c
> @@ -183,6 +183,17 @@ static int fsl_ehci_drv_probe(struct platform_device *pdev)
>  	return retval;
>  }
>  
> +static bool usb_phy_clk_valid(struct usb_hcd *hcd)
> +{
> +	void __iomem *non_ehci = hcd->regs;
> +	bool ret = true;
> +
> +	if (!(ioread32be(non_ehci + FSL_SOC_USB_CTRL) & PHY_CLK_VALID))
> +		ret = false;
> +
> +	return ret;
> +}
> +
>  static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
>  			       enum fsl_usb2_phy_modes phy_mode,
>  			       unsigned int port_offset)
> @@ -226,6 +237,16 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
>  		/* fall through */
>  	case FSL_USB2_PHY_UTMI:
>  	case FSL_USB2_PHY_UTMI_DUAL:
> +		/* PHY_CLK_VALID bit is de-featured from all controller
> +		 * versions below 2.4 and is to be checked only for
> +		 * internal UTMI phy
> +		 */
> +		if (pdata->controller_ver > FSL_USB_VER_2_4 &&
> +		    pdata->have_sysif_regs && !usb_phy_clk_valid(hcd)) {
> +			dev_err(dev, "USB PHY clock invalid\n");
> +			return -EINVAL;
> +		}
> +
>  		if (pdata->have_sysif_regs && pdata->controller_ver) {
>  			/* controller version 1.6 or above */
>  			tmp = ioread32be(non_ehci + FSL_SOC_USB_CTRL);
> @@ -249,17 +270,11 @@ static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
>  		break;
>  	}
>  
> -	/*
> -	 * check PHY_CLK_VALID to determine phy clock presence before writing
> -	 * to portsc
> -	 */
> -	if (pdata->check_phy_clk_valid) {
> -		if (!(ioread32be(non_ehci + FSL_SOC_USB_CTRL) &
> -		    PHY_CLK_VALID)) {
> -			dev_warn(hcd->self.controller,
> -				 "USB PHY clock invalid\n");
> -			return -EINVAL;
> -		}
> +	if (pdata->have_sysif_regs &&
> +	    pdata->controller_ver > FSL_USB_VER_1_6 &&
> +		!usb_phy_clk_valid(hcd)) {

This is still wrong.  The line above should be indented four characters 
less than it is: the '!' should line up with the 'p' in the line above 
it.

Alan Stern

> +		dev_warn(hcd->self.controller, "USB PHY clock invalid\n");
> +		return -EINVAL;
>  	}
>  
>  	ehci_writel(ehci, portsc, &ehci->regs->port_status[port_offset]);
> diff --git a/drivers/usb/host/ehci-fsl.h b/drivers/usb/host/ehci-fsl.h
> index cbc4220..9d18c6e 100644
> --- a/drivers/usb/host/ehci-fsl.h
> +++ b/drivers/usb/host/ehci-fsl.h
> @@ -50,4 +50,7 @@
>  #define UTMI_PHY_EN             (1<<9)
>  #define ULPI_PHY_CLK_SEL        (1<<10)
>  #define PHY_CLK_VALID		(1<<17)
> +
> +/* Retry count for checking UTMI PHY CLK validity */
> +#define UTMI_PHY_CLK_VALID_CHK_RETRY 5
>  #endif				/* _EHCI_FSL_H */
>