Re: msm8996: qcom-qmp: apq8096-db820c fails to boot, reset back to fastboot and locks up

[Niklas Cassel]

On Tue, Jun 11, 2019 at 07:12:25PM +0200, Niklas Cassel wrote:
> On Mon, Jun 10, 2019 at 03:44:01PM +0200, Paolo Pisati wrote:
> > From time to time, my apq8096-db820c fails to boot to userspace, reset back to
> > fastboot and locks up: to easily reproduce the issue, i'm boot looping using a
> > cron job with a 1 min reboot entry on the board while leaving a "while 1; do
> > fastboot boot boot.img; done" on the host pc.
> > 
> > The issue is present in mainline up to 5.2-rc4, using defconfig and:
> > 
> > CONFIG_SCSI_UFS_QCOM=y
> > CONFIG_PHY_QCOM_QMP=y
> > CONFIG_PHY_QCOM_UFS=y
> > 
> > but was present in previous releases too (e.g. 4.14., 4.19, etc qcom-lt or
> > mainline), where it's even easier to reproduce (e.g. takes way less reboots to
> > trigger it).
> 
> Hello Paolo,
> 
> I have a guess of what is going on.
> db820c has 3 PCIe controllers,
> that shares a singe QMP block (that has clocks, regulators, and resets).
> The QMP block has 3 PCIe PHYs, that have their own clocks and resets.
> 
> > 
> > These are the last lines printed out:
> > ...
> > [    7.407209] qcom-qmp-phy 34000.phy: Registered Qcom-QMP phy
> > [    7.448058] qcom-qmp-phy 7410000.phy: Registered Qcom-QMP phy
> > [    7.461859] ufs_qcom_phy_qmp_14nm 627000.phy: invalid resource
> > [    7.535434] qcom-qmp-phy 34000.phy: phy common block init timed-out
> 
> ^^ here the phy_init() called from pcie-qcom.c
> which ends up to a call to qcom_qmp_phy_enable()
> 
> which has this code:
> 
>         ret = qcom_qmp_phy_com_init(qphy);
>         if (ret)
>                 return ret;
> 
> qcom_qmp_phy_com_init() has this code:
> 
>         if (qmp->init_count++) {
>                 mutex_unlock(&qmp->phy_mutex);
>                 return 0;
>         }
> 
> qcom_qmp_phy_com_init() later fails,
> since the common block init time out, so the qmp driver
> disables clocks, asserts reset, and disables regulators
> 
> 
> > [    7.538596] phy phy-34000.phy.0: phy init failed --> -110
> > [    7.550891] qcom-pcie: probe of 600000.pcie failed with error -110
> 
> ^^ here the first PCIe controller instance fails to probe
> 
> > [    7.619008] qcom-pcie 608000.pcie: 608000.pcie supply vddpe-3v3 not found,
> > using dummy regulator
> 
> ^^ here the second PCIe controller is probed.
> 
> it will call phy_init()
> 
> which will again call qcom_qmp_phy_enable() which will call
> qcom_qmp_phy_com_init()
> 
> where this code:
> 
>         if (qmp->init_count++) {
>                 mutex_unlock(&qmp->phy_mutex);
>                 return 0;
>         }
> 
> now will return 0,
> 
> so clocks will never be enabled, resets never deasserted, regulators
> never enabled.
> 
> since qcom_qmp_phy_com_init() returns success in this case,
> qcom_qmp_phy_enable() will try to continue with the init,
> and writes to disabled hardware is usually not a good idea.
> 
> I think the proper fix for this is:
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
> index cd91b4179b10..22352e3b0ec5 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
> @@ -1490,7 +1490,7 @@ static int qcom_qmp_phy_enable(struct phy *phy)
>  
>         ret = qcom_qmp_phy_com_init(qphy);
>         if (ret)
> -               return ret;
> +               goto err_lane_rst;
>  
>         if (cfg->has_lane_rst) {
>                 ret = reset_control_deassert(qphy->lane_rst);
> 
> 
> 
> Kind regards,
> Niklas
> 
> > 
> > Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
> > S - QC_IMAGE_VERSION_STRING=BOOT.XF.1.0-00301
> > S - IMAGE_VARIANT_STRING=M8996LAB
> > S - OEM_IMAGE_VERSION_STRING=crm-ubuntu68
> > S - Boot Interface: UFS
> > S - Secure Boot: Off
> > ...
> > 
> > Full boot here: https://pastebin.ubuntu.com/p/rtjVrD3yzk/
> > 
> > Any idea what is going on? Am i doing something wrong?
> > -- 
> > bye,
> > p.

Adding Vivek.