Re: [PATCH] arm64: dts: qcom: msm8998: Node ordering, address cleanups

From: Vinod Koul
Date: Wed Jul 24 2019 - 11:36:50 EST

Next message: Christoph Hellwig: "Re: add swiotlb support to arm32"
Previous message: Dan Murphy: "Re: [PATCH v12 1/5] can: m_can: Create a m_can platform framework"
In reply to: Bjorn Andersson: "Re: [PATCH] arm64: dts: qcom: msm8998: Node ordering, address cleanups"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On 22-07-19, 09:58, Jeffrey Hugo wrote:
> DT nodes should be ordered by address, then node name, and finally label.
> The msm8998 dtsi does not follow this, so clean it up by reordering the
> nodes. While we are at it, extend the addresses to be fully 32-bits wide
> so that ordering is easy to determine when adding new nodes. Also, two
> or so nodes had the wrong address value in their node name (did not match
> the reg property), so fix those up as well.
>
> Hopefully going forward, things can be maintained so that a cleanup like
> this is not needed.

lgtm, ideally I would have liked that we reg addresses fixed first and
then sort the file (remember a patch should do one thing)

But then any cleanup is better to do :) so:

Reviewed-by: Vinod Koul <vkoul@xxxxxxxxxx>

>
> Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@xxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/msm8998.dtsi | 254 +++++++++++++-------------
> 1 file changed, 127 insertions(+), 127 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
> index c13ed7aeb1e0..4b66a1c588f8 100644
> --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
> @@ -787,14 +787,22 @@
> ranges = <0 0 0 0xffffffff>;
> compatible = "simple-bus";
>
> - rpm_msg_ram: memory@68000 {
> + gcc: clock-controller@100000 {
> + compatible = "qcom,gcc-msm8998";
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + #power-domain-cells = <1>;
> + reg = <0x00100000 0xb0000>;
> + };
> +
> + rpm_msg_ram: memory@778000 {
> compatible = "qcom,rpm-msg-ram";
> - reg = <0x778000 0x7000>;
> + reg = <0x00778000 0x7000>;
> };
>
> qfprom: qfprom@780000 {
> compatible = "qcom,qfprom";
> - reg = <0x780000 0x621c>;
> + reg = <0x00780000 0x621c>;
> #address-cells = <1>;
> #size-cells = <1>;
>
> @@ -804,47 +812,10 @@
> };
> };
>
> - gcc: clock-controller@100000 {
> - compatible = "qcom,gcc-msm8998";
> - #clock-cells = <1>;
> - #reset-cells = <1>;
> - #power-domain-cells = <1>;
> - reg = <0x100000 0xb0000>;
> - };
> -
> - tlmm: pinctrl@3400000 {
> - compatible = "qcom,msm8998-pinctrl";
> - reg = <0x3400000 0xc00000>;
> - interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> - gpio-controller;
> - #gpio-cells = <0x2>;
> - interrupt-controller;
> - #interrupt-cells = <0x2>;
> - };
> -
> - spmi_bus: spmi@800f000 {
> - compatible = "qcom,spmi-pmic-arb";
> - reg = <0x800f000 0x1000>,
> - <0x8400000 0x1000000>,
> - <0x9400000 0x1000000>,
> - <0xa400000 0x220000>,
> - <0x800a000 0x3000>;
> - reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> - interrupt-names = "periph_irq";
> - interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>;
> - qcom,ee = <0>;
> - qcom,channel = <0>;
> - #address-cells = <2>;
> - #size-cells = <0>;
> - interrupt-controller;
> - #interrupt-cells = <4>;
> - cell-index = <0>;
> - };
> -
> tsens0: thermal@10ab000 {
> compatible = "qcom,msm8998-tsens", "qcom,tsens-v2";
> - reg = <0x10ab000 0x1000>, /* TM */
> - <0x10aa000 0x1000>; /* SROT */
> + reg = <0x010ab000 0x1000>, /* TM */
> + <0x010aa000 0x1000>; /* SROT */
>
> #qcom,sensors = <14>;
> #thermal-sensor-cells = <1>;
> @@ -852,8 +823,8 @@
>
> tsens1: thermal@10ae000 {
> compatible = "qcom,msm8998-tsens", "qcom,tsens-v2";
> - reg = <0x10ae000 0x1000>, /* TM */
> - <0x10ad000 0x1000>; /* SROT */
> + reg = <0x010ae000 0x1000>, /* TM */
> + <0x010ad000 0x1000>; /* SROT */
>
> #qcom,sensors = <8>;
> #thermal-sensor-cells = <1>;
> @@ -943,16 +914,107 @@
> };
> };
>
> + ufshc: ufshc@1da4000 {
> + compatible = "qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0";
> + reg = <0x01da4000 0x2500>;
> + interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
> + phys = <&ufsphy_lanes>;
> + phy-names = "ufsphy";
> + lanes-per-direction = <2>;
> + power-domains = <&gcc UFS_GDSC>;
> + #reset-cells = <1>;
> +
> + clock-names =
> + "core_clk",
> + "bus_aggr_clk",
> + "iface_clk",
> + "core_clk_unipro",
> + "ref_clk",
> + "tx_lane0_sync_clk",
> + "rx_lane0_sync_clk",
> + "rx_lane1_sync_clk";
> + clocks =
> + <&gcc GCC_UFS_AXI_CLK>,
> + <&gcc GCC_AGGRE1_UFS_AXI_CLK>,
> + <&gcc GCC_UFS_AHB_CLK>,
> + <&gcc GCC_UFS_UNIPRO_CORE_CLK>,
> + <&rpmcc RPM_SMD_LN_BB_CLK1>,
> + <&gcc GCC_UFS_TX_SYMBOL_0_CLK>,
> + <&gcc GCC_UFS_RX_SYMBOL_0_CLK>,
> + <&gcc GCC_UFS_RX_SYMBOL_1_CLK>;
> + freq-table-hz =
> + <50000000 200000000>,
> + <0 0>,
> + <0 0>,
> + <37500000 150000000>,
> + <0 0>,
> + <0 0>,
> + <0 0>,
> + <0 0>;
> +
> + resets = <&gcc GCC_UFS_BCR>;
> + reset-names = "rst";
> + };
> +
> + ufsphy: phy@1da7000 {
> + compatible = "qcom,msm8998-qmp-ufs-phy";
> + reg = <0x01da7000 0x18c>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + clock-names =
> + "ref",
> + "ref_aux";
> + clocks =
> + <&gcc GCC_UFS_CLKREF_CLK>,
> + <&gcc GCC_UFS_PHY_AUX_CLK>;
> +
> + reset-names = "ufsphy";
> + resets = <&ufshc 0>;
> +
> + ufsphy_lanes: lanes@1da7400 {
> + reg = <0x01da7400 0x128>,
> + <0x01da7600 0x1fc>,
> + <0x01da7c00 0x1dc>,
> + <0x01da7800 0x128>,
> + <0x01da7a00 0x1fc>;
> + #phy-cells = <0>;
> + };
> + };
> +
> tcsr_mutex_regs: syscon@1f40000 {
> compatible = "syscon";
> - reg = <0x1f40000 0x20000>;
> + reg = <0x01f40000 0x20000>;
> };
>
> - apcs_glb: mailbox@9820000 {
> - compatible = "qcom,msm8998-apcs-hmss-global";
> - reg = <0x17911000 0x1000>;
> + tlmm: pinctrl@3400000 {
> + compatible = "qcom,msm8998-pinctrl";
> + reg = <0x03400000 0xc00000>;
> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> + gpio-controller;
> + #gpio-cells = <0x2>;
> + interrupt-controller;
> + #interrupt-cells = <0x2>;
> + };
>
> - #mbox-cells = <1>;
> + spmi_bus: spmi@800f000 {
> + compatible = "qcom,spmi-pmic-arb";
> + reg = <0x0800f000 0x1000>,
> + <0x08400000 0x1000000>,
> + <0x09400000 0x1000000>,
> + <0x0a400000 0x220000>,
> + <0x0800a000 0x3000>;
> + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
> + interrupt-names = "periph_irq";
> + interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>;
> + qcom,ee = <0>;
> + qcom,channel = <0>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> + interrupt-controller;
> + #interrupt-cells = <4>;
> + cell-index = <0>;
> };
>
> usb3: usb@a8f8800 {
> @@ -1044,7 +1106,7 @@
>
> sdhc2: sdhci@c0a4900 {
> compatible = "qcom,sdhci-msm-v4";
> - reg = <0xc0a4900 0x314>, <0xc0a4000 0x800>;
> + reg = <0x0c0a4900 0x314>, <0x0c0a4000 0x800>;
> reg-names = "hc_mem", "core_mem";
>
> interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
> @@ -1149,6 +1211,16 @@
> #size-cells = <0>;
> };
>
> + blsp2_uart1: serial@c1b0000 {
> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> + reg = <0x0c1b0000 0x1000>;
> + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>,
> + <&gcc GCC_BLSP2_AHB_CLK>;
> + clock-names = "core", "iface";
> + status = "disabled";
> + };
> +
> blsp2_i2c0: i2c@c1b5000 {
> compatible = "qcom,i2c-qup-v2.2.1";
> reg = <0x0c1b5000 0x600>;
> @@ -1239,14 +1311,11 @@
> #size-cells = <0>;
> };
>
> - blsp2_uart1: serial@c1b0000 {
> - compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
> - reg = <0xc1b0000 0x1000>;
> - interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
> - clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>,
> - <&gcc GCC_BLSP2_AHB_CLK>;
> - clock-names = "core", "iface";
> - status = "disabled";
> + apcs_glb: mailbox@17911000 {
> + compatible = "qcom,msm8998-apcs-hmss-global";
> + reg = <0x17911000 0x1000>;
> +
> + #mbox-cells = <1>;
> };
>
> timer@17920000 {
> @@ -1320,75 +1389,6 @@
> redistributor-stride = <0x0 0x20000>;
> interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> };
> -
> - ufshc: ufshc@1da4000 {
> - compatible = "qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0";
> - reg = <0x01da4000 0x2500>;
> - interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
> - phys = <&ufsphy_lanes>;
> - phy-names = "ufsphy";
> - lanes-per-direction = <2>;
> - power-domains = <&gcc UFS_GDSC>;
> - #reset-cells = <1>;
> -
> - clock-names =
> - "core_clk",
> - "bus_aggr_clk",
> - "iface_clk",
> - "core_clk_unipro",
> - "ref_clk",
> - "tx_lane0_sync_clk",
> - "rx_lane0_sync_clk",
> - "rx_lane1_sync_clk";
> - clocks =
> - <&gcc GCC_UFS_AXI_CLK>,
> - <&gcc GCC_AGGRE1_UFS_AXI_CLK>,
> - <&gcc GCC_UFS_AHB_CLK>,
> - <&gcc GCC_UFS_UNIPRO_CORE_CLK>,
> - <&rpmcc RPM_SMD_LN_BB_CLK1>,
> - <&gcc GCC_UFS_TX_SYMBOL_0_CLK>,
> - <&gcc GCC_UFS_RX_SYMBOL_0_CLK>,
> - <&gcc GCC_UFS_RX_SYMBOL_1_CLK>;
> - freq-table-hz =
> - <50000000 200000000>,
> - <0 0>,
> - <0 0>,
> - <37500000 150000000>,
> - <0 0>,
> - <0 0>,
> - <0 0>,
> - <0 0>;
> -
> - resets = <&gcc GCC_UFS_BCR>;
> - reset-names = "rst";
> - };
> -
> - ufsphy: phy@1da7000 {
> - compatible = "qcom,msm8998-qmp-ufs-phy";
> - reg = <0x01da7000 0x18c>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - clock-names =
> - "ref",
> - "ref_aux";
> - clocks =
> - <&gcc GCC_UFS_CLKREF_CLK>,
> - <&gcc GCC_UFS_PHY_AUX_CLK>;
> -
> - reset-names = "ufsphy";
> - resets = <&ufshc 0>;
> -
> - ufsphy_lanes: lanes@1da7400 {
> - reg = <0x01da7400 0x128>,
> - <0x01da7600 0x1fc>,
> - <0x01da7c00 0x1dc>,
> - <0x01da7800 0x128>,
> - <0x01da7a00 0x1fc>;
> - #phy-cells = <0>;
> - };
> - };
> };
> };
>
> --
> 2.17.1

--
~Vinod

Next message: Christoph Hellwig: "Re: add swiotlb support to arm32"
Previous message: Dan Murphy: "Re: [PATCH v12 1/5] can: m_can: Create a m_can platform framework"
In reply to: Bjorn Andersson: "Re: [PATCH] arm64: dts: qcom: msm8998: Node ordering, address cleanups"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]