Re: [PATCH 1/4] i3c: master: detach and free device if pre_assign_dyn_addr() fails

[Boris Brezillon]

On Thu, 29 Aug 2019 15:23:30 +0000
Vitor Soares <Vitor.Soares@xxxxxxxxxxxx> wrote:

> From: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxx>
> Date: Thu, Aug 29, 2019 at 15:35:20
> 
> > On Thu, 29 Aug 2019 13:53:24 +0000
> > Vitor Soares <Vitor.Soares@xxxxxxxxxxxx> wrote:
> >   
> > > Hi Boris,
> > > 
> > > From: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxx>
> > > Date: Thu, Aug 29, 2019 at 11:41:15
> > >   
> > > > +Przemek
> > > > 
> > > > Please try to Cc active I3C contributors so they get a chance to
> > > > comment on your patches.    
> > > 
> > > I can do that next time.
> > >   
> > > > 
> > > > On Thu, 29 Aug 2019 12:19:32 +0200
> > > > Vitor Soares <Vitor.Soares@xxxxxxxxxxxx> wrote:
> > > >     
> > > > > On pre_assing_dyn_addr() the devices that fail:
> > > > >   i3c_master_setdasa_locked()
> > > > >   i3c_master_reattach_i3c_dev()
> > > > >   i3c_master_retrieve_dev_info()
> > > > > 
> > > > > are kept in memory and master->bus.devs list. This makes the i3c devices
> > > > > without a dynamic address are sent on DEFSLVS CCC command. Fix this by
> > > > > detaching and freeing the devices that fail on pre_assign_dyn_addr().    
> > > > 
> > > > I don't think removing those entries is a good strategy, as one might
> > > > want to try to use a different dynamic address if the requested one
> > > > is not available.    
> > > 
> > > Do you mean same 'assigned-address' attribute in DT?  
> > 
> > Yes, or say it's another device that got the address we want and this
> > device doesn't want to release the address (I'm assuming the !SA case).
> >   
> > > 
> > > If so, it is checked here:
> > > 
> > > static int i3c_master_bus_init(struct i3c_master_controller *master)
> > > ...
> > > 	list_for_each_entry(i3cboardinfo, &master->boardinfo.i3c, node) {
> > > 		struct i3c_device_info info = {
> > > 			.static_addr = i3cboardinfo->static_addr,
> > > 		};
> > > 
> > > 		if (i3cboardinfo->init_dyn_addr) {
> > > 			status = i3c_bus_get_addr_slot_status(&master->bus,
> > > 			^
> > > 						i3cboardinfo->init_dyn_addr);
> > > 			if (status != I3C_ADDR_SLOT_FREE) {
> > > 				ret = -EBUSY;
> > > 				goto err_detach_devs;
> > > 			}
> > > 		}
> > > 
> > > 		i3cdev = i3c_master_alloc_i3c_dev(master, &info);
> > > 		if (IS_ERR(i3cdev)) {
> > > 			ret = PTR_ERR(i3cdev);
> > > 			goto err_detach_devs;
> > > 		}
> > > 
> > > 		i3cdev->boardinfo = i3cboardinfo;
> > > 
> > > 		ret = i3c_master_attach_i3c_dev(master, i3cdev);
> > > 		if (ret) {
> > > 			i3c_master_free_i3c_dev(i3cdev);
> > > 			goto err_detach_devs;
> > > 		}
> > > 	}
> > > ...
> > > 
> > > and later if it fails i3c_master_pre_assign_dyn_addr(), the device can 
> > > participate in Enter Dynamic Address Assignment process.
> > > I may need to check the boardinfo->init_dyn_addr status on 
> > > i3c_master_add_i3c_dev_locked before i3c_master_setnewda_locked().  
> > 
> > I need to double check but I thought we were already handling that case
> > properly.  
> 
> Yes, it is handled in the code above.

No, I meant the 'assign init_dyn_addr even if !SA', and the code I
pointed in my other reply tends to confirm that this is something we
already take into account (maybe not correctly, but the code is here).

> 
> >   
> > >   
> > > > Why not simply skipping entries that have ->dyn_addr
> > > > set to 0 when preparing a DEFSLVS frame    
> > > 
> > > I considered that solution too but if the device isn't enumerated why 
> > > should it be attached and kept in memory?  
> > 
> > Might be a device that supports HJ, and in that case we might want the
> > controller to reserve a slot in its device table for that device.
> > Anyway, it doesn't hurt to have it around as long as we don't pass the
> > device through DEFSLVS if it doesn't have a dynamic address. I really
> > prefer to keep the logic unchanged and fix it if it needs to be fixed.  
> 
> Well, we aren't reserving a slot because we need another one to attach 
> the device when it is enumerated and hence a device may be using 2 slots 
> in the controller.

Right, you shouldn't reserve a slot when ->static_address == 0 &&
->dynamic_address == 0, but I still don't see where the problem is with
the solution we have right now, sorry. Note that even if you reserve a
slot in that case, the device only occupies 2 slots for a short amount
of time, because the add_i3c_dev() logic will detect that the descriptor
already exists and reattach the device with its new address.

> It may cause problems in HC with reduced slots and it is another reason 
> why I think we should detach device without dynamic address after the 
> enumeration phase.

Can you please try the approach I suggest? => fix the existing logic to
make it work without this "free undiscovered dev desc, reallocate later"
dance.