Re: [PATCH 05/11] drm/bridge: analogix-anx78xx: correct value of TX_P0

[Brian Masney]

On Mon, Sep 16, 2019 at 01:32:58PM +0200, Enric Balletbo i Serra wrote:
> Hi,
> 
> On 16/9/19 12:49, Laurent Pinchart wrote:
> > Hi Brian,
> > 
> > On Mon, Sep 16, 2019 at 06:36:14AM -0400, Brian Masney wrote:
> >> On Mon, Sep 16, 2019 at 12:02:09PM +0200, Andrzej Hajda wrote:
> >>> On 15.08.2019 02:48, Brian Masney wrote:
> >>>> When attempting to configure this driver on a Nexus 5 phone (msm8974),
> >>>> setting up the dummy i2c bus for TX_P0 would fail due to an -EBUSY
> >>>> error. The downstream MSM kernel sources [1] shows that the proper value
> >>>> for TX_P0 is 0x78, not 0x70, so correct the value to allow device
> >>>> probing to succeed.
> >>>>
> >>>> [1] https://github.com/AICP/kernel_lge_hammerhead/blob/n7.1/drivers/video/slimport/slimport_tx_reg.h
> >>>>
> >>>> Signed-off-by: Brian Masney <masneyb@xxxxxxxxxxxxx>
> >>>> ---
> >>>>  drivers/gpu/drm/bridge/analogix-anx78xx.h | 2 +-
> >>>>  1 file changed, 1 insertion(+), 1 deletion(-)
> >>>>
> >>>> diff --git a/drivers/gpu/drm/bridge/analogix-anx78xx.h b/drivers/gpu/drm/bridge/analogix-anx78xx.h
> >>>> index 25e063bcecbc..bc511fc605c9 100644
> >>>> --- a/drivers/gpu/drm/bridge/analogix-anx78xx.h
> >>>> +++ b/drivers/gpu/drm/bridge/analogix-anx78xx.h
> >>>> @@ -6,7 +6,7 @@
> >>>>  #ifndef __ANX78xx_H
> >>>>  #define __ANX78xx_H
> >>>>  
> >>>> -#define TX_P0				0x70
> >>>> +#define TX_P0				0x78
> >>>
> >>>
> >>> This bothers me little. There are no upstream users, grepping android
> >>> sources suggests that both values can be used [1][2]  (grep for "#define
> >>> TX_P0"), moreover there is code suggesting both values can be valid [3].
> >>>
> >>> Could you verify datasheet which i2c slave addresses are valid for this
> >>> chip, if both I guess this patch should be reworked.
> >>>
> >>>
> >>> [1]:
> >>> https://android.googlesource.com/kernel/msm/+/android-msm-flo-3.4-jb-mr2/drivers/misc/slimport_anx7808/slimport_tx_reg.h
> >>>
> >>> [2]:
> >>> https://github.com/AndroidGX/SimpleGX-MM-6.0_H815_20d/blob/master/drivers/video/slimport/anx7812/slimport7812_tx_reg.h
> >>>
> >>> [3]:
> >>> https://github.com/commaai/android_kernel_leeco_msm8996/blob/master/drivers/video/msm/mdss/dp/slimport_custom_declare.h#L73
> >>
> >> This address is 0x78 on my Nexus 5. Given [3] above it looks like we
> >> need to support both addresses. What do you think about moving these
> >> addresses into device tree?
> > 
> > Assuming that the device supports different addresses (I can't validate
> > that as I don't have access to the datasheet), and different addresses
> > need to be used on different systems, then the address to be used needs
> > to be provided by the firmware (DT in this case). Two options are
> > possible, either specifying the address explicitly in the device's DT
> > node, or specifying free addresses (in the form of a white list or black
> > list) and allocating an address from that pool. The latter has been
> > discussed in a BoF at the Linux Plumbers Conference last week,
> > https://linuxplumbersconf.org/event/4/contributions/542/.
> > 
> >> The downstream and upstream kernel sources divide these addresses by two
> >> to get the i2c address. Here's the code in upstream:
> >>
> >> https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/bridge/analogix-anx78xx.c#L1353
> >> https://elixir.bootlin.com/linux/latest/source/drivers/gpu/drm/bridge/analogix-anx78xx.c#L41
> >>
> >> I'm not sure why the actual i2c address isn't used in this code.
> > 
> 
> The ANX7802/12/14/16 has a slave I2C bus that provides the interface to access
> or control the chip from the AP. The I2C slave addresses used to control the
> ANX7802/12/14/16 are 70h, 72h, 7Ah, 7Eh and 80h. Every address allows you to
> access to different registers of the chip and AFAICS is not configurable.
> 
> I don't think these addresses should be configured via DT but for the driver itself.
> 
> My wild guess is that the ANX7808 has different addresses, but I don't have the
> datasheet of this version.

I'm able to communicate with the 7808 on my Nexus 5 using the 0x78
address. Given that the addresses appear to be fixed per model, maybe it
makes sense to drop the address #defines and add the addresses to the
data pointer in the driver's of_match_table like so:

static const struct of_device_id anx78xx_match_table[] = {
        { .compatible = "analogix,anx7808", .data = PTR_TO_7808_ADDRS },
        { .compatible = "analogix,anx7812", .data = PTR_TO_781X_ADDRS },
        { .compatible = "analogix,anx7814", .data = PTR_TO_781X_ADDRS },
        { .compatible = "analogix,anx7818", .data = PTR_TO_781X_ADDRS },
        { /* sentinel */ },
};

Brian