Re: [PATCH v2] serial: sprd: Add polling IO support

[hhome liu]

Baolin Wang <baolin.wang@xxxxxxxxxx> ä2019å9æ19æåå äå11:21åéï
>
> Hi,
>
> On Thu, 19 Sep 2019 at 11:10, Lanqing Liu <liuhhome@xxxxxxxxx> wrote:
> >
> > In order to access the UART without the interrupts, the kernel uses
> > the basic polling methods for IO with the device. With these methods
> > implemented, it is now possible to enable kgdb during early boot over serial.
> >
> > Signed-off-by: Lanqing Liu <liuhhome@xxxxxxxxx>
> > ---
> > Change from v1:
> >  - Add poll_init() support.
>
> Looks good to me and the KGDB can work well on my board, so feel free
> to add my tags:
> Reviewed-by: Baolin Wang <baolin.wang@xxxxxxxxxx>
> Tested-by: Baolin Wang <baolin.wang@xxxxxxxxxx>
>
ok, thanks
> > ---
> >  drivers/tty/serial/sprd_serial.c | 33 +++++++++++++++++++++++++++++++++
> >  1 file changed, 33 insertions(+)
> >
> > diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c
> > index 73d71a4..d833160 100644
> > --- a/drivers/tty/serial/sprd_serial.c
> > +++ b/drivers/tty/serial/sprd_serial.c
> > @@ -911,6 +911,34 @@ static void sprd_pm(struct uart_port *port, unsigned int state,
> >         }
> >  }
> >
> > +#ifdef CONFIG_CONSOLE_POLL
> > +static int sprd_poll_init(struct uart_port *port)
> > +{
> > +       if (port->state->pm_state != UART_PM_STATE_ON) {
> > +               sprd_pm(port, UART_PM_STATE_ON, 0);
> > +               port->state->pm_state = UART_PM_STATE_ON;
> > +       }
> > +
> > +       return 0;
> > +}
> > +
> > +static int sprd_poll_get_char(struct uart_port *port)
> > +{
> > +       while (!(serial_in(port, SPRD_STS1) & SPRD_RX_FIFO_CNT_MASK))
> > +               cpu_relax();
> > +
> > +       return serial_in(port, SPRD_RXD);
> > +}
> > +
> > +static void sprd_poll_put_char(struct uart_port *port, unsigned char ch)
> > +{
> > +       while (serial_in(port, SPRD_STS1) & SPRD_TX_FIFO_CNT_MASK)
> > +               cpu_relax();
> > +
> > +       serial_out(port, SPRD_TXD, ch);
> > +}
> > +#endif
> > +
> >  static const struct uart_ops serial_sprd_ops = {
> >         .tx_empty = sprd_tx_empty,
> >         .get_mctrl = sprd_get_mctrl,
> > @@ -928,6 +956,11 @@ static void sprd_pm(struct uart_port *port, unsigned int state,
> >         .config_port = sprd_config_port,
> >         .verify_port = sprd_verify_port,
> >         .pm = sprd_pm,
> > +#ifdef CONFIG_CONSOLE_POLL
> > +       .poll_init      = sprd_poll_init,
> > +       .poll_get_char  = sprd_poll_get_char,
> > +       .poll_put_char  = sprd_poll_put_char,
> > +#endif
> >  };
> >
> >  #ifdef CONFIG_SERIAL_SPRD_CONSOLE
> > --
> > 1.9.1
> >
>
>
> --
> Baolin Wang
> Best Regards