[PATCH] spi: atmel: Fix crash when using more than 4 gpio CS
From: Gregory CLEMENT
Date: Thu Sep 19 2019 - 11:39:49 EST
Even when using a gpio as chip select, the registers controlling the
hardware chip select have to be configured. However any of the 4
hardware CS can be controlled.
Until now, the gpio index was used to match an hardware chip select,
which limited the number of CS than can be used. Using more than 4
gpios leads to the following kernel crash:
WARNING: CPU: 0 PID: 1 at drivers/spi/spi-atmel.c:1293 atmel_spi_transfer_one_message+0x8b0/0x8ec
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.3.0+ #24
Hardware name: Atmel SAMA5
[<c010d914>] (unwind_backtrace) from [<c010ad84>] (show_stack+0x10/0x14)
[<c010ad84>] (show_stack) from [<c0117d28>] (__warn+0xd8/0xf0)
[<c0117d28>] (__warn) from [<c0117d80>] (warn_slowpath_null+0x40/0x48)
[<c0117d80>] (warn_slowpath_null) from [<c04b21dc>] (atmel_spi_transfer_one_message+0x8b0/0x8ec)
[<c04b21dc>] (atmel_spi_transfer_one_message) from [<c04afb20>] (__spi_pump_messages+0x330/0x510)
[<c04afb20>] (__spi_pump_messages) from [<c04afe5c>] (__spi_sync+0x150/0x158)
[<c04afe5c>] (__spi_sync) from [<c04afe88>] (spi_sync+0x24/0x3c)
[<c04afe88>] (spi_sync) from [<c04aff88>] (spi_write_then_read+0xe8/0x1a8)
[<c04aff88>] (spi_write_then_read) from [<c0454da0>] (_regmap_raw_read+0xec/0x148)
[<c0454da0>] (_regmap_raw_read) from [<c0454f6c>] (regmap_raw_read+0x110/0x238)
[<c0454f6c>] (regmap_raw_read) from [<c04551f4>] (regmap_bulk_read+0x160/0x19c)
[<c04551f4>] (regmap_bulk_read) from [<c0517744>] (rv3029_get_sr+0x28/0x64)
[<c0517744>] (rv3029_get_sr) from [<c0518184>] (rv3029_probe+0x5c/0x260)
[<c0518184>] (rv3029_probe) from [<c04acf90>] (spi_drv_probe+0x88/0xac)
[<c04acf90>] (spi_drv_probe) from [<c043fec8>] (really_probe+0xf0/0x2c8)
[<c043fec8>] (really_probe) from [<c0440214>] (driver_probe_device+0x60/0x16c)
[<c0440214>] (driver_probe_device) from [<c04404c0>] (device_driver_attach+0x58/0x60)
[<c04404c0>] (device_driver_attach) from [<c0440520>] (__driver_attach+0x58/0xcc)
[<c0440520>] (__driver_attach) from [<c043e318>] (bus_for_each_dev+0x78/0xc0)
[<c043e318>] (bus_for_each_dev) from [<c043f33c>] (bus_add_driver+0x15c/0x1e0)
[<c043f33c>] (bus_add_driver) from [<c0440d2c>] (driver_register+0x74/0x108)
[<c0440d2c>] (driver_register) from [<c0a1cb44>] (rv30x9_init+0x38/0x68)
[<c0a1cb44>] (rv30x9_init) from [<c0102608>] (do_one_initcall+0x58/0x1c0)
[<c0102608>] (do_one_initcall) from [<c0a00e88>] (kernel_init_freeable+0x124/0x1c0)
[<c0a00e88>] (kernel_init_freeable) from [<c0774dc0>] (kernel_init+0x8/0x10c)
[<c0774dc0>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
Exception stack(0xcf429fb0 to 0xcf429ff8)
9fa0: 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000
With this patch, when using a gpio CS, the hardware CS0 is always
used. Thanks to this, there is no more limitation for the number of
gpio CS we can use.
Fixes: 754ce4f29937 ("[PATCH] SPI: atmel_spi driver")
Cc: stable@xxxxxxxxxxxxxxx
Signed-off-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxx>
---
drivers/spi/spi-atmel.c | 44 ++++++++++++++++++++++++++++++-----------
1 file changed, 33 insertions(+), 11 deletions(-)
diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index acf318e7330c..bb94f5927819 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -353,22 +353,28 @@ static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
{
struct atmel_spi_device *asd = spi->controller_state;
u32 mr;
+ u8 chip_select;
+
+ if (as->use_cs_gpios)
+ chip_select = 0;
+ else
+ chip_select = spi->chip_select;
if (atmel_spi_is_v2(as)) {
- spi_writel(as, CSR0 + 4 * spi->chip_select, asd->csr);
+ spi_writel(as, CSR0 + 4 * chip_select, asd->csr);
/* For the low SPI version, there is a issue that PDC transfer
* on CS1,2,3 needs SPI_CSR0.BITS config as SPI_CSR1,2,3.BITS
*/
spi_writel(as, CSR0, asd->csr);
if (as->caps.has_wdrbt) {
spi_writel(as, MR,
- SPI_BF(PCS, ~(0x01 << spi->chip_select))
+ SPI_BF(PCS, ~(0x01 << chip_select))
| SPI_BIT(WDRBT)
| SPI_BIT(MODFDIS)
| SPI_BIT(MSTR));
} else {
spi_writel(as, MR,
- SPI_BF(PCS, ~(0x01 << spi->chip_select))
+ SPI_BF(PCS, ~(0x01 << chip_select))
| SPI_BIT(MODFDIS)
| SPI_BIT(MSTR));
}
@@ -390,8 +396,8 @@ static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
}
mr = spi_readl(as, MR);
- mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
- if (as->use_cs_gpios && spi->chip_select != 0)
+ mr = SPI_BFINS(PCS, ~(1 << chip_select), mr);
+ if (as->use_cs_gpios && chip_select != 0)
gpiod_set_value(asd->npcs_pin, 1);
spi_writel(as, MR, mr);
}
@@ -403,12 +409,18 @@ static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
{
struct atmel_spi_device *asd = spi->controller_state;
u32 mr;
+ u8 chip_select;
+
+ if (as->use_cs_gpios)
+ chip_select = 0;
+ else
+ chip_select = spi->chip_select;
/* only deactivate *this* device; sometimes transfers to
* another device may be active when this routine is called.
*/
mr = spi_readl(as, MR);
- if (~SPI_BFEXT(PCS, mr) & (1 << spi->chip_select)) {
+ if (~SPI_BFEXT(PCS, mr) & (1 << chip_select)) {
mr = SPI_BFINS(PCS, 0xf, mr);
spi_writel(as, MR, mr);
}
@@ -417,7 +429,7 @@ static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
if (!as->use_cs_gpios)
spi_writel(as, CR, SPI_BIT(LASTXFER));
- else if (atmel_spi_is_v2(as) || spi->chip_select != 0)
+ else if (atmel_spi_is_v2(as) || chip_select != 0)
gpiod_set_value(asd->npcs_pin, 0);
}
@@ -844,6 +856,12 @@ static int atmel_spi_set_xfer_speed(struct atmel_spi *as,
{
u32 scbr, csr;
unsigned long bus_hz;
+ u8 chip_select;
+
+ if (as->use_cs_gpios)
+ chip_select = 0;
+ else
+ chip_select = spi->chip_select;
/* v1 chips start out at half the peripheral bus speed. */
bus_hz = as->spi_clk;
@@ -872,9 +890,9 @@ static int atmel_spi_set_xfer_speed(struct atmel_spi *as,
xfer->speed_hz, scbr, bus_hz);
return -EINVAL;
}
- csr = spi_readl(as, CSR0 + 4 * spi->chip_select);
+ csr = spi_readl(as, CSR0 + 4 * chip_select);
csr = SPI_BFINS(SCBR, scbr, csr);
- spi_writel(as, CSR0 + 4 * spi->chip_select, csr);
+ spi_writel(as, CSR0 + 4 * chip_select, csr);
return 0;
}
@@ -1238,8 +1256,12 @@ static int atmel_spi_setup(struct spi_device *spi)
"setup: bpw %u mode 0x%x -> csr%d %08x\n",
bits, spi->mode, spi->chip_select, csr);
- if (!atmel_spi_is_v2(as))
- spi_writel(as, CSR0 + 4 * spi->chip_select, csr);
+ if (!atmel_spi_is_v2(as)) {
+ if (as->use_cs_gpios)
+ spi_writel(as, CSR0, csr);
+ else
+ spi_writel(as, CSR0 + 4 * spi->chip_select, csr);
+ }
return 0;
}
--
2.23.0