Re: [PATCH v2 00/11] Move PMC clocks into Tegra PMC driver

[Sowjanya Komatineni]

On 11/27/19 6:31 AM, Dmitry Osipenko wrote:
> 27.11.2019 07:59, Sowjanya Komatineni ÐÐÑÐÑ:
> > Tegra PMC has clk_out_1, clk_out_2, clk_out_3 and blink controls which
> > are currently registered by Tegra clock driver using clk_regiser_mux and
> > clk_register_gate which performs direct Tegra PMC register access.
> >
> > When Tegra PMC is in secure mode, any access from non-secure world will
> > not go through.
> >
> > This patch series adds these Tegra PMC clocks and blink controls to Tegra
> > PMC driver with PMC as clock provider and removed them from Tegra clock
> > driver. This also adds PMC specific clock id's to use in device tree and
> > removed clock ids of PMC clock from Tegra clock driver.
> >
> > This series also includes patch to update clock provider from tegra_car
> > to pmc in the device tree tegra210-smaug.dts that uses clk_out_2 from PMC.
> >
> > [v2]:	Changes between v1 and v2 are
> > 	- v2 includes patches for adding clk_out_1, clk_out_2, clk_out_3,
> > 	  blink controls to Tegra PMC driver and removing clk-tegra-pmc.
> > 	- feedback related to pmc clocks in Tegra PMC driver from v1
> > 	- Removed patches for WB0 PLLM overrides and PLLE IDDQ PMC programming
> > 	  by the clock driver using helper functions from Tegra PMC.
> >
> >   	  Note:
> > 	  To use helper functions from PMC driver, PMC early init need to
> > 	  happen prior to using helper functions and these helper functions are
> > 	  for PLLM Override and PLLE IDDQ programming in PMC during PLLM/PLLE
> > 	  clock registration which happen in clock_init prior to Tegra PMC
> > 	  probe.
> > 	  Moving PLLM/PLLE clocks registration to happen after Tegra PMC
> > 	  impacts other clocks EMC, MC and corresponding tegra_emc_init and
> > 	  tegra_mc_init.
> > 	  This implementation of configuring PMC registers thru helper
> > 	  functions in clock driver needs proper changes across PMC, Clock,
> > 	  EMC and MC inits to have it work across all Tegra platforms.
> >
> > 	  Currently PLLM Override is not enabled in the bootloader so proper
> > 	  patches for this fix will be taken care separately.
> Hello Sowjanya,
>
> Could you please clarify what do you mean by "PLLM Override not enabled
> in bootloader"?
>
> There is T124 Nyan Big Chromebook which is supported in upstream kernel,
> it has PLLM Override set by bootloader. I also have T30 Nexus 7 tablet
> which has the PLLM Override set by bootloader as well. It's not clear to
> me whether this patch series is supposed to break these devices. If the
> breakage is the case here, then I'm afraid you can't postpone supporting
> the PLLM Override and a full-featured implementation is needed.

Hi Dmitry,

Secure boot currently is enabled only on Tegra210 and Tegra210 
bootloader doesn't enable PLLM override.

So PLLM override/PLLE IDDQ being in clock driver currently will not 
break on any of existing Tegra platforms.

> I briefly tried to test this series on T30 and this time it doesn't hang
> on boot, but somehow WiFi MMC card detection is broken. AFAIK, the WiFi
> chip uses the Blink clock source and the clock should be enabled by the
> MMC core because this is how DT part looks like:
>
> brcm_wifi_pwrseq: wifi-pwrseq {
> 	compatible = "mmc-pwrseq-simple";
> 	clocks = <&pmc TEGRA_PMC_CLK_BLINK>;
> 	clock-names = "ext_clock";
> 	reset-gpios =  <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_LOW>;
> 	post-power-on-delay-ms = <300>;
> 	power-off-delay-us = <300>;
> };
>
> BTW, I  tried this series on a T20 device which also uses the Blink
> clock for WiFi card and it works. So looks like this patchset has some
> problem in regards to the T30 PMC clocks implementation.
>
> [snip]

Blink init state is set to true for both Tegra20 and Tegra30 and all go 
through the same blink programming sequence.

Will try to add more debug messages to dump registers and will test 
blink through device tree on T30 and will get back...