RE: [RESEND v6 06/13] spi: imx: fix ERR009165
From: Robin Gong
Date: Tue Mar 10 2020 - 04:27:49 EST
On 2020/03/10 Sascha Hauer <s.hauer@xxxxxxxxxxxxxx> wrote:
> On Tue, Mar 10, 2020 at 07:31:55PM +0800, Robin Gong wrote:
> > Change to XCH mode even in dma mode, please refer to the below
> > errata:
> > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.
> >
> nxp.com%2Fdocs%2Fen%2Ferrata%2FIMX6DQCE.pdf&data=02%7C01%7C
> yibin.g
> >
> ong%40nxp.com%7Ccbabce268dfd4b0a0e2a08d7c4c62ff6%7C686ea1d3bc2b4c
> 6fa92
> >
> cd99c5c301635%7C0%7C1%7C637194227793913712&sdata=Q5N49T4jgX
> TcdTzsB
> > 3D0saK2%2Fzj0R4gnJcGR%2Bd70Fm4%3D&reserved=0
> >
> > Signed-off-by: Robin Gong <yibin.gong@xxxxxxx>
> > Acked-by: Mark Brown <broonie@xxxxxxxxxx>
> > ---
> > drivers/spi/spi-imx.c | 17 ++++++++++-------
> > 1 file changed, 10 insertions(+), 7 deletions(-)
> >
> > diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c index
> > f4f28a4..842a86e 100644
> > --- a/drivers/spi/spi-imx.c
> > +++ b/drivers/spi/spi-imx.c
> > @@ -585,8 +585,9 @@ static int mx51_ecspi_prepare_transfer(struct
> spi_imx_data *spi_imx,
> > ctrl |= mx51_ecspi_clkdiv(spi_imx, t->speed_hz, &clk);
> > spi_imx->spi_bus_clk = clk;
> >
> > + /* ERR009165: work in XHC mode as PIO */
> > if (spi_imx->usedma)
> > - ctrl |= MX51_ECSPI_CTRL_SMC;
> > + ctrl &= ~MX51_ECSPI_CTRL_SMC;
>
> 'ctrl' was read from the hardware. In the dma case it was set explicitly, but it
> was never cleared for a PIO transfer. This looked wrong before this patch. Now
> with this patch it looks even more wrong:
> We clear a bit that has never been set and we only do this for DMA, when for
> the PIO case it definitly must be cleared. Drop the if clause.
Good point, ACK.
>
> >
> > writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
> >
> > @@ -612,12 +613,14 @@ static int mx51_ecspi_prepare_transfer(struct
> > spi_imx_data *spi_imx,
> >
> > static void mx51_setup_wml(struct spi_imx_data *spi_imx) {
> > + u32 tx_wml = 0;
> > +
> > /*
> > * Configure the DMA register: setup the watermark
> > * and enable DMA request.
> > */
> > writel(MX51_ECSPI_DMA_RX_WML(spi_imx->wml - 1) |
> > - MX51_ECSPI_DMA_TX_WML(spi_imx->wml) |
> > + MX51_ECSPI_DMA_TX_WML(tx_wml) |
>
> tx_wml is never assigned any other value than 0. Drop the variable.
That's prepared for 07/13 patch which may assign spi_imx->wml to tx_wml.
>
> > MX51_ECSPI_DMA_RXT_WML(spi_imx->wml) |
> > MX51_ECSPI_DMA_TEDEN | MX51_ECSPI_DMA_RXDEN |
> > MX51_ECSPI_DMA_RXTDEN, spi_imx->base + MX51_ECSPI_DMA);
> @@ -1171,7
> > +1174,11 @@ static int spi_imx_dma_configure(struct spi_master *master)
> > tx.direction = DMA_MEM_TO_DEV;
> > tx.dst_addr = spi_imx->base_phys + MXC_CSPITXDATA;
> > tx.dst_addr_width = buswidth;
> > - tx.dst_maxburst = spi_imx->wml;
> > + /*
> > + * For ERR009165 with tx_wml = 0 could enlarge burst size to fifo size
> > + * to speed up fifo filling as possible.
> > + */
> > + tx.dst_maxburst = spi_imx->devtype_data->fifo_size;
> > ret = dmaengine_slave_config(master->dma_tx, &tx);
> > if (ret) {
> > dev_err(spi_imx->dev, "TX dma configuration failed with %d\n",
> > ret); @@ -1265,10 +1272,6 @@ static int spi_imx_sdma_init(struct
> > device *dev, struct spi_imx_data *spi_imx, {
> > int ret;
> >
> > - /* use pio mode for i.mx6dl chip TKT238285 */
> > - if (of_machine_is_compatible("fsl,imx6dl"))
> > - return 0;
>
> So with this patch it becomes possible to do DMA on i.MX6dl, but it is
> mentioned nowhere.
That's a common IP issue but caught on i.mx6dl at that time, so this time I didn't mention
i.mx6dl.
>
> Sascha
>
> --
> Pengutronix e.K. |
> |
> Steuerwalder Str. 21 |
> https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.pe
> ngutronix.de%2F&data=02%7C01%7Cyibin.gong%40nxp.com%7Ccbabce2
> 68dfd4b0a0e2a08d7c4c62ff6%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%
> 7C1%7C637194227793913712&sdata=TL%2BheiNsYVPld3qyzWjF6yQZgH2
> HLdVFxzFeK3MupTc%3D&reserved=0 |
> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0
> |
> Amtsgericht Hildesheim, HRA 2686 | Fax:
> +49-5121-206917-5555 |