Re: [RFC] clk: vc5: Add bindings for output configurations

[Adam Ford]

On Fri, Mar 27, 2020 at 4:41 AM Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:
>
> Hi Adam,
>
> CC Marek
>
> On Thu, Mar 26, 2020 at 10:33 PM Adam Ford <aford173@xxxxxxxxx> wrote:
> > The Versaclock can be purchased in a non-programmed configuration.
> > If that is the case, the driver needs to configure the chip to
> > output the correct signal type, voltage and slew.
> >
> > This RFC is proposing an additional binding to allow non-programmed
> > chips to be configured beyond their default configuration.
> >
> > Signed-off-by: Adam Ford <aford173@xxxxxxxxx>
> >
> > diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt
> > index 05a245c9df08..4bc46ed9ba4a 100644
> > --- a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt
> > +++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt
> > @@ -30,6 +30,25 @@ Required properties:
> >                 - 5p49v5933 and
> >                 - 5p49v5935: (optional) property not present or "clkin".
> >
> > +For all output ports, an option child node can be used to specify:
> > +
> > +- mode: can be one of
> > +                 - LVPECL: Low-voltage positive/psuedo emitter-coupled logic
> > +                 - CMOS
> > +                 - HCSL
> > +                 - LVDS: Low voltage differential signal
> > +
> > +- voltage-level:  can be one of the following microvolts
> > +                 - 1800000
> > +                 - 2500000
> > +                 - 3300000
> > +-  slew: Percent of normal, can be one of
> > +                 - P80
> > +                 - P85
> > +                 - P90
> > +                 - P100
>
> Why the P prefixes? Can't you just use integer values?
> After the conversion to json-schema, these values can be validated, too.
>
> > +
> > +
> >  ==Mapping between clock specifier and physical pins==
> >
> >  When referencing the provided clock in the DT using phandle and
> > @@ -62,6 +81,8 @@ clock specifier, the following mapping applies:
> >
> >  ==Example==
> >
> > +#include <dt-bindings/versaclock.h>
>
> Does not exist?

Not yet.  Before actually coding anything, I wanted to get feedback on
how the bindings should look.  In this file would be definitions of
terms like P80, CMOS, and the other items that are defined for mode
and slew.

>
> > +
> >  /* 25MHz reference crystal */
> >  ref25: ref25m {
> >         compatible = "fixed-clock";
> > @@ -80,6 +101,13 @@ i2c-master-node {
> >                 /* Connect XIN input to 25MHz reference */
> >                 clocks = <&ref25m>;
> >                 clock-names = "xin";
> > +
> > +               ports@1 {
> > +                       reg = <1>;
> > +                       mode = <CMOS>;
> > +                       pwr_sel = <1800000>;
> > +                       slew = <P80>;
> > +               };
> >         };
> >  };
>
> Gr{oetje,eeting}s,
>
>                         Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
>                                 -- Linus Torvalds