Re: [PATCH v2] ARM: imx: allow to disable board specific PHY fixups

[Russell King - ARM Linux admin]

On Mon, Mar 30, 2020 at 10:33:03AM -0700, Florian Fainelli wrote:
> 
> 
> On 3/29/2020 10:26 PM, Oleksij Rempel wrote:
> > Hi Andrew,
> > 
> > On Sun, Mar 29, 2020 at 05:08:54PM +0200, Andrew Lunn wrote:
> >> On Sun, Mar 29, 2020 at 01:04:57PM +0200, Oleksij Rempel wrote:
> >>
> >> Hi Oleksij
> >>
> >>> +config DEPRECATED_PHY_FIXUPS
> >>> +	bool "Enable deprecated PHY fixups"
> >>> +	default y
> >>> +	---help---
> >>> +	  In the early days it was common practice to configure PHYs by adding a
> >>> +	  phy_register_fixup*() in the machine code. This practice turned out to
> >>> +	  be potentially dangerous, because:
> >>> +	  - it affects all PHYs in the system
> >>> +	  - these register changes are usually not preserved during PHY reset
> >>> +	    or suspend/resume cycle.
> >>> +	  - it complicates debugging, since these configuration changes were not
> >>> +	    done by the actual PHY driver.
> >>> +	  This option allows to disable all fixups which are identified as
> >>> +	  potentially harmful and give the developers a chance to implement the
> >>> +	  proper configuration via the device tree (e.g.: phy-mode) and/or the
> >>> +	  related PHY drivers.
> >>
> >> This appears to be an IMX only problem. Everybody else seems to of got
> >> this right. There is no need to bother everybody with this new
> >> option. Please put this in arch/arm/mach-mxs/Kconfig and have IMX in
> >> the name.
> > 
> > Actually, all fixups seems to do wring thing:
> > arch/arm/mach-davinci/board-dm644x-evm.c:915:		phy_register_fixup_for_uid(LXT971_PHY_ID, LXT971_PHY_MASK,
> > 
> > Increased MII drive strength. Should be probably enabled by the PHY
> > driver.
> > 
> > arch/arm/mach-imx/mach-imx6q.c:167:		phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
> > arch/arm/mach-imx/mach-imx6q.c:169:		phy_register_fixup_for_uid(PHY_ID_KSZ9031, MICREL_PHY_ID_MASK,
> > arch/arm/mach-imx/mach-imx6q.c:171:		phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffef,
> > arch/arm/mach-imx/mach-imx6q.c:173:		phy_register_fixup_for_uid(PHY_ID_AR8035, 0xffffffef,

As far as I'm concerned, the AR8035 fixup is there with good reason.
It's not just "random" but is required to make the AR8035 usable with
the iMX6 SoCs.  Not because of a board level thing, but because it's
required for the AR8035 to be usable with an iMX6 SoC.

So, having it registered by the iMX6 SoC code is entirely logical and
correct.

That's likely true of the AR8031 situation as well.

I can't speak for any of the others.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 10.2Mbps down 587kbps up