Re: [RFC v2 03/11] tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state

[Amit Pundir]

Hi Rajendra,

On Wed, 12 Aug 2020 at 11:18, Rajendra Nayak <rnayak@xxxxxxxxxxxxxx> wrote:
>
>
> On 8/12/2020 7:03 AM, John Stultz wrote:
> > On Tue, Aug 11, 2020 at 4:11 PM John Stultz <john.stultz@xxxxxxxxxx> wrote:
> >>
> >> On Wed, Mar 20, 2019 at 2:49 AM Rajendra Nayak <rnayak@xxxxxxxxxxxxxx> wrote:
> >>>
> >>> geni serial needs to express a perforamnce state requirement on CX
> >>> depending on the frequency of the clock rates. Use OPP table from
> >>> DT to register with OPP framework and use dev_pm_opp_set_rate() to
> >>> set the clk/perf state.
> >>>
> >>> Signed-off-by: Rajendra Nayak <rnayak@xxxxxxxxxxxxxx>
> >>> Signed-off-by: Stephen Boyd <swboyd@xxxxxxxxxxxx>
> >>> ---
> >>>   drivers/tty/serial/qcom_geni_serial.c | 15 +++++++++++++--
> >>>   1 file changed, 13 insertions(+), 2 deletions(-)
> >>>
> >>
> >> Hey,
> >>    I just wanted to follow up on this patch, as I've bisected it
> >> (a5819b548af0) down as having broken qca bluetooth on the Dragonboard
> >> 845c.
> >>
> >> I haven't yet had time to debug it yet, but wanted to raise the issue
> >> in case anyone else has seen similar trouble.
> >
> > So I dug in a bit further, and this chunk seems to be causing the issue:
> >> @@ -961,7 +963,7 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport,
> >>                  goto out_restart_rx;
> >>
> >>          uport->uartclk = clk_rate;
> >> -       clk_set_rate(port->se.clk, clk_rate);
> >> +       dev_pm_opp_set_rate(port->dev, clk_rate);
> >>          ser_clk_cfg = SER_CLK_EN;
> >>          ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
> >>
> >
> >
> > With that applied, I see the following errors in dmesg and bluetooth
> > fails to function:
> > [    4.763467] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate:
> > failed to find OPP for freq 102400000 (-34)
> > [    4.773493] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate:
> > failed to find OPP for freq 102400000 (-34)
> >
> > With just that chunk reverted on linus/HEAD, bluetooth seems to work ok.
>
> This seems like the same issue that was also reported on venus [1] because the
> clock frequency tables apparently don;t exactly match the achievable clock
> frequencies (which we also used to construct the OPP tables)
>
> Can you try updating the OPP table for QUP to have 102400000 instead of the
> current 100000000 and see if that fixes it?

That worked. Thanks.

Should this change be common to base sdm845.dtsi or platform specific dts?
For what it's worth, we see this BT breakage on PocoF1 phone too.

Regards,
Amit Pundir


>
> [1] https://lkml.org/lkml/2020/7/27/507
>
> >
> > thanks
> > -john
> >
>
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation