Re: [RFC v2 03/11] tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state

[Rajendra Nayak]

On 8/12/2020 1:05 PM, Amit Pundir wrote:
> Hi Rajendra,
>
> On Wed, 12 Aug 2020 at 11:18, Rajendra Nayak <rnayak@xxxxxxxxxxxxxx> wrote:
> > On 8/12/2020 7:03 AM, John Stultz wrote:
> > > On Tue, Aug 11, 2020 at 4:11 PM John Stultz <john.stultz@xxxxxxxxxx> wrote:
> > > > On Wed, Mar 20, 2019 at 2:49 AM Rajendra Nayak <rnayak@xxxxxxxxxxxxxx> wrote:
> > > > > geni serial needs to express a perforamnce state requirement on CX
> > > > > depending on the frequency of the clock rates. Use OPP table from
> > > > > DT to register with OPP framework and use dev_pm_opp_set_rate() to
> > > > > set the clk/perf state.
> > > > >
> > > > > Signed-off-by: Rajendra Nayak <rnayak@xxxxxxxxxxxxxx>
> > > > > Signed-off-by: Stephen Boyd <swboyd@xxxxxxxxxxxx>
> > > > > ---
> > > > >    drivers/tty/serial/qcom_geni_serial.c | 15 +++++++++++++--
> > > > >    1 file changed, 13 insertions(+), 2 deletions(-)
> > > >
> > > > Hey,
> > > >     I just wanted to follow up on this patch, as I've bisected it
> > > > (a5819b548af0) down as having broken qca bluetooth on the Dragonboard
> > > > 845c.
> > > >
> > > > I haven't yet had time to debug it yet, but wanted to raise the issue
> > > > in case anyone else has seen similar trouble.
> > >
> > > So I dug in a bit further, and this chunk seems to be causing the issue:
> > > > @@ -961,7 +963,7 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport,
> > > >                   goto out_restart_rx;
> > > >
> > > >           uport->uartclk = clk_rate;
> > > > -       clk_set_rate(port->se.clk, clk_rate);
> > > > +       dev_pm_opp_set_rate(port->dev, clk_rate);
> > > >           ser_clk_cfg = SER_CLK_EN;
> > > >           ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
> > >
> > >
> > > With that applied, I see the following errors in dmesg and bluetooth
> > > fails to function:
> > > [    4.763467] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate:
> > > failed to find OPP for freq 102400000 (-34)
> > > [    4.773493] qcom_geni_serial 898000.serial: dev_pm_opp_set_rate:
> > > failed to find OPP for freq 102400000 (-34)
> > >
> > > With just that chunk reverted on linus/HEAD, bluetooth seems to work ok.
> >
> > This seems like the same issue that was also reported on venus [1] because the
> > clock frequency tables apparently don;t exactly match the achievable clock
> > frequencies (which we also used to construct the OPP tables)
> >
> > Can you try updating the OPP table for QUP to have 102400000 instead of the
> > current 100000000 and see if that fixes it?
>
> That worked. Thanks.
>
> Should this change be common to base sdm845.dtsi or platform specific dts?
> For what it's worth, we see this BT breakage on PocoF1 phone too.

Thanks for confirming, it will have to be part of the SoC dtsi, and I am
guessing a similar change is perhaps also needed on sc7180.
I will send a patch out to fix the OPP tables for both.

> Regards,
> Amit Pundir
>
>
> > [1] https://lkml.org/lkml/2020/7/27/507
> >
> > > thanks
> > > -john
> >
> > --
> > QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> > of Code Aurora Forum, hosted by The Linux Foundation

--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation