Re: [PATCH V4 1/4] arm64: dts: sc7180: Add wakeup support over UART RX

From: Matthias Kaehlcke
Date: Thu Sep 03 2020 - 12:05:36 EST

On Thu, Sep 03, 2020 at 08:34:55PM +0530, satya priya wrote:
> Add the necessary pinctrl and interrupts to make UART wakeup capable.
>
> If QUP function is selected in sleep state, UART RTS/RFR is pulled high
> during suspend and BT SoC not able to send wakeup bytes. So, configure
> GPIO mode in sleep state to keep it low during suspend.
>
> Signed-off-by: satya priya <skakit@xxxxxxxxxxxxxx>
> Reviewed-by: Akash Asthana <akashast@xxxxxxxxxxxxxx>
> ---
> Changes in V2:
> - As per Matthias's comment added wakeup support for all the UARTs
> of SC7180.
>
> Changes in V3:
> - No change.
>
> Changes in V4:
> - As per Matthias's comment, added the reason for configuring GPIO
> mode for sleep state in commit text.
>
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 98 ++++++++++++++++++++++++++++++------
> 1 file changed, 84 insertions(+), 14 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index d46b383..855b13e 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -793,9 +793,11 @@
> reg = <0 0x00880000 0 0x4000>;
> clock-names = "se";
> clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "sleep";
> pinctrl-0 = <&qup_uart0_default>;
> - interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-1 = <&qup_uart0_sleep>;
> + interrupts-extended = <&intc GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>,
> + <&tlmm 37 IRQ_TYPE_EDGE_FALLING>;
> power-domains = <&rpmhpd SC7180_CX>;
> operating-points-v2 = <&qup_opp_table>;
> interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
> @@ -845,9 +847,11 @@
> reg = <0 0x00884000 0 0x4000>;
> clock-names = "se";
> clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "sleep";
> pinctrl-0 = <&qup_uart1_default>;
> - interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-1 = <&qup_uart1_sleep>;
> + interrupts-extended = <&intc GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
> + <&tlmm 3 IRQ_TYPE_EDGE_FALLING>;
> power-domains = <&rpmhpd SC7180_CX>;
> operating-points-v2 = <&qup_opp_table>;
> interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
> @@ -931,9 +935,11 @@
> reg = <0 0x0088c000 0 0x4000>;
> clock-names = "se";
> clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "sleep";
> pinctrl-0 = <&qup_uart3_default>;
> - interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-1 = <&qup_uart3_sleep>;
> + interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
> + <&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
> power-domains = <&rpmhpd SC7180_CX>;
> operating-points-v2 = <&qup_opp_table>;
> interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
> @@ -1017,9 +1023,11 @@
> reg = <0 0x00894000 0 0x4000>;
> clock-names = "se";
> clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "sleep";
> pinctrl-0 = <&qup_uart5_default>;
> - interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-1 = <&qup_uart5_sleep>;
> + interrupts-extended = <&intc GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>,
> + <&tlmm 28 IRQ_TYPE_EDGE_FALLING>;
> power-domains = <&rpmhpd SC7180_CX>;
> operating-points-v2 = <&qup_opp_table>;
> interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
> @@ -1084,9 +1092,11 @@
> reg = <0 0x00a80000 0 0x4000>;
> clock-names = "se";
> clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "sleep";
> pinctrl-0 = <&qup_uart6_default>;
> - interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-1 = <&qup_uart6_sleep>;
> + interrupts-extended = <&intc GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>,
> + <&tlmm 62 IRQ_TYPE_EDGE_FALLING>;
> power-domains = <&rpmhpd SC7180_CX>;
> operating-points-v2 = <&qup_opp_table>;
> interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
> @@ -1256,9 +1266,11 @@
> reg = <0 0x00a90000 0 0x4000>;
> clock-names = "se";
> clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "sleep";
> pinctrl-0 = <&qup_uart10_default>;
> - interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-1 = <&qup_uart10_sleep>;
> + interrupts-extended = <&intc GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>,
> + <&tlmm 89 IRQ_TYPE_EDGE_FALLING>;
> power-domains = <&rpmhpd SC7180_CX>;
> operating-points-v2 = <&qup_opp_table>;
> interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
> @@ -1308,9 +1320,11 @@
> reg = <0 0x00a94000 0 0x4000>;
> clock-names = "se";
> clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
> - pinctrl-names = "default";
> + pinctrl-names = "default", "sleep";
> pinctrl-0 = <&qup_uart11_default>;
> - interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-1 = <&qup_uart11_sleep>;
> + interrupts-extended = <&intc GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
> + <&tlmm 56 IRQ_TYPE_EDGE_FALLING>;
> power-domains = <&rpmhpd SC7180_CX>;
> operating-points-v2 = <&qup_opp_table>;
> interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
> @@ -1638,6 +1652,14 @@
> };
> };
>
> + qup_uart0_sleep: qup-uart0-sleep {
> + pinmux {
> + pins = "gpio34", "gpio35",
> + "gpio36", "gpio37";
> + function = "gpio";
> + };
> + };
> +
> qup_uart1_default: qup-uart1-default {
> pinmux {
> pins = "gpio0", "gpio1",
> @@ -1646,6 +1668,14 @@
> };
> };
>
> + qup_uart1_sleep: qup-uart1-sleep {
> + pinmux {
> + pins = "gpio0", "gpio1",
> + "gpio2", "gpio3";
> + function = "gpio";
> + };
> + };
> +
> qup_uart2_default: qup-uart2-default {
> pinmux {
> pins = "gpio15", "gpio16";
> @@ -1661,6 +1691,14 @@
> };
> };
>
> + qup_uart3_sleep: qup-uart3-sleep {
> + pinmux {
> + pins = "gpio38", "gpio39",
> + "gpio40", "gpio41";
> + function = "gpio";
> + };
> + };
> +
> qup_uart4_default: qup-uart4-default {
> pinmux {
> pins = "gpio115", "gpio116";
> @@ -1676,6 +1714,14 @@
> };
> };
>
> + qup_uart5_sleep: qup-uart5-sleep {
> + pinmux {
> + pins = "gpio25", "gpio26",
> + "gpio27", "gpio28";
> + function = "gpio";
> + };
> + };
> +
> qup_uart6_default: qup-uart6-default {
> pinmux {
> pins = "gpio59", "gpio60",
> @@ -1684,6 +1730,14 @@
> };
> };
>
> + qup_uart6_sleep: qup-uart6-sleep {
> + pinmux {
> + pins = "gpio59", "gpio60",
> + "gpio61", "gpio62";
> + function = "gpio";
> + };
> + };
> +
> qup_uart7_default: qup-uart7-default {
> pinmux {
> pins = "gpio6", "gpio7";
> @@ -1713,6 +1767,14 @@
> };
> };
>
> + qup_uart10_sleep: qup-uart10-sleep {
> + pinmux {
> + pins = "gpio86", "gpio87",
> + "gpio88", "gpio89";
> + function = "gpio";
> + };
> + };
> +
> qup_uart11_default: qup-uart11-default {
> pinmux {
> pins = "gpio53", "gpio54",
> @@ -1721,6 +1783,14 @@
> };
> };
>
> + qup_uart11_sleep: qup-uart11-sleep {
> + pinmux {
> + pins = "gpio53", "gpio54",
> + "gpio55", "gpio56";
> + function = "gpio";
> + };
> + };
> +
> sdc1_on: sdc1-on {
> pinconf-clk {
> pins = "sdc1_clk";

It seems only the RTS pin actually requires a pinmux change. One could
argue that only the muxing of this pin should be changed in sleep mode.
But well, changing all pins to GPIO simplifies the config, so I guess
it's ok as long as there are no side effects.

I noticed you changed only the UARTs that have RTS/CTS signals. Do the
others not support wakeup? I understand that the pinmux change isn't
needed for these UARTs, since they have no RTS signal, however I'd expect
them to need the 'interrupts-extended' entry if they support wakeup.