Re: [PATCH V5 2/4] arm64: dts: qcom: sc7180: Add necessary pinctrl and interrupt config for BT UART

[Bjorn Andersson]

On Fri 11 Sep 05:15 CDT 2020, skakit@xxxxxxxxxxxxxx wrote:

> On 2020-09-10 20:10, Doug Anderson wrote:
> > Hi,
> > 
> > On Thu, Sep 10, 2020 at 5:55 AM satya priya <skakit@xxxxxxxxxxxxxx>
> > wrote:
> > > 
> > > Add a suitable sleep configuration for uart3 to support Bluetooth
> > > wakeup.
> > > 
> > > If QUP function is selected in sleep state, UART RTS/RFR is pulled
> > > high
> > > during suspend and BT SoC not able to send wakeup bytes. So, configure
> > > GPIO mode in sleep state to keep it low during suspend.
> > > 
> > > Signed-off-by: satya priya <skakit@xxxxxxxxxxxxxx>
> > > Reviewed-by: Akash Asthana <akashast@xxxxxxxxxxxxxx>
> > > ---
> > > Changes in V2:
> > >  - This patch adds sleep state for BT UART. Newly added in V2.
> > > 
> > > Changes in V3:
> > >  - Remove "output-high" for TX from both sleep and default states
> > >    as it is not required. Configure pull-up for TX in sleep state.
> > > 
> > > Changes in V4:
> > >  - As per Matthias's comment, removed drive-strength for sleep state
> > >    and fixed nit-pick.
> > > 
> > > Changes in V5:
> > >  - As per Matthias's comments, moved pinmux change for sleep state,
> > >    pinctrl and interrupt config to the board specific file.
> > > 
> > >  arch/arm64/boot/dts/qcom/sc7180-idp.dts | 48
> > > +++++++++++++++++++++++++++++++++
> > >  1 file changed, 48 insertions(+)
> > 
> > Similar comment to patch #1 in that this applies only to the IDP board
> > but that's not obvious from ${SUBJECT}
> > 
> 
> Okay.
> 
> > 
> > > diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > index 04888df..e529a41 100644
> > > --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > @@ -344,6 +344,10 @@
> > >  };
> > > 
> > >  &uart3 {
> > > +       pinctrl-names = "default", "sleep";
> > > +       pinctrl-1 = <&qup_uart3_sleep>;
> > > +       interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
> > > +                               <&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
> > 
> > You need a:
> > 
> > /delete-property/interrupts;
> > 
> > ...or, alternatively, a patch before this one that converts all the
> > UARTs in sc7180 to just use interrupts-extended.
> > 
> 
> Sure, I will add this. But I think when both are added,
> "interrupts-extended" will get priority as per [1] and there wouldn't be any
> problem.
> 

You're indeed correct, please stick with what you have.

Regards,
Bjorn

> [1] https://www.kernel.org/doc/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> 
> > 
> > >         status = "okay";
> > 
> > Slight nit is that usually I see the status line first.  All the other
> > instances in this file have it that way.  Can you match?
> > 
> 
> Ok, will correct it.
> 
> > 
> > 
> > 
> > -Doug