Re: [RESEND PATCH v3 1/3] dt-bindings: pinctrl: Add bindings for pinctrl-mchp-sgpio driver

[Rob Herring]

On Tue, Oct 06, 2020 at 04:25:30PM +0200, Lars Povlsen wrote:
> This adds DT bindings for the Microsemi/Microchip SGPIO controller,
> bindings microchip,sparx5-sgpio, mscc,ocelot-sgpio and
> mscc,luton-sgpio.
> 
> Signed-off-by: Lars Povlsen <lars.povlsen@xxxxxxxxxxxxx>
> ---
>  .../pinctrl/microchip,sparx5-sgpio.yaml       | 127 ++++++++++++++++++
>  1 file changed, 127 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
> new file mode 100644
> index 000000000000..e3618ed28165
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
> @@ -0,0 +1,127 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/microchip,sparx5-sgpio.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Microsemi/Microchip Serial GPIO controller
> +
> +maintainers:
> +  - Lars Povlsen <lars.povlsen@xxxxxxxxxxxxx>
> +
> +description: |
> +  By using a serial interface, the SIO controller significantly extend
> +  the number of available GPIOs with a minimum number of additional
> +  pins on the device. The primary purpose of the SIO controllers is to
> +  connect control signals from SFP modules and to act as an LED
> +  controller.
> +
> +properties:
> +  $nodename:
> +    pattern: "^gpio@[0-9a-f]+$"
> +
> +  compatible:
> +    enum:
> +      - microchip,sparx5-sgpio
> +      - mscc,ocelot-sgpio
> +      - mscc,luton-sgpio
> +
> +  "#address-cells":
> +    const: 1
> +
> +  "#size-cells":
> +    const: 0
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  microchip,sgpio-port-ranges:
> +    description: This is a sequence of tuples, defining intervals of
> +      enabled ports in the serial input stream. The enabled ports must
> +      match the hardware configuration in order for signals to be
> +      properly written/read to/from the controller holding
> +      registers. Being tuples, then number of arguments must be
> +      even. The tuples mast be ordered (low, high) and are
> +      inclusive. Arguments must be between 0 and 31.
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    minItems: 2
> +    maxItems: 64
> +
> +  microchip,sgpio-frequency:
> +    description: The sgpio controller frequency (Hz). This dictates
> +      the serial bitstream speed, which again affects the latency in
> +      getting control signals back and forth between external shift
> +      registers. The speed must be no larger than half the system
> +      clock, and larger than zero.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    minimum: 1
> +    default: 12500000
> +
> +patternProperties:
> +  "^gpio-(port|controller)@[01]$":

gpio@... is correct here as the node is a gpio-controller (no, we're 
not consistent).

> +    type: object
> +    properties:
> +      compatible:
> +        const: microchip,sparx5-sgpio-bank
> +
> +      reg:
> +        maxItems: 1
> +
> +      gpio-controller: true
> +
> +      '#gpio-cells':
> +        const: 3
> +
> +      ngpios:
> +        minimum: 1
> +        maximum: 128
> +
> +    required:
> +      - compatible
> +      - reg
> +      - gpio-controller
> +      - '#gpio-cells'
> +      - ngpios
> +
> +    additionalProperties: false
> +
> +additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - microchip,sgpio-port-ranges
> +  - "#address-cells"
> +  - "#size-cells"
> +
> +examples:
> +  - |
> +    sgpio2: gpio@1101059c {
> +    	#address-cells = <1>;
> +    	#size-cells = <0>;
> +    	compatible = "microchip,sparx5-sgpio";
> +    	clocks = <&sys_clk>;
> +    	pinctrl-0 = <&sgpio2_pins>;
> +    	pinctrl-names = "default";
> +    	reg = <0x1101059c 0x100>;
> +        microchip,sgpio-port-ranges = <0 0 16 18 28 31>;

Since it's tuples, do:

<0 0>, <16 18>, <28 31>

> +        microchip,sgpio-frequency = <25000000>;

Some whitespace issues here.


> +    	sgpio_in2: gpio-controller@0 {
> +            reg = <0>;
> +            compatible = "microchip,sparx5-sgpio-bank";
> +            gpio-controller;
> +            #gpio-cells = <3>;
> +            ngpios = <96>;
> +    	};
> +    	sgpio_out2: gpio-controller@1 {
> +            compatible = "microchip,sparx5-sgpio-bank";
> +            reg = <1>;
> +            gpio-controller;
> +            #gpio-cells = <3>;
> +            ngpios = <96>;
> +    	};
> +    };
> --
> 2.25.1