Re: [PATCH 0/6] Add support for SDM630/660 Camera Subsystem

[Robert Foss]

Hey Angelo,

Thanks for submitting this, and fixing other issues as you went.

I sent out some SoBs which should have been Reviewed-bys, so if you
add them to your commit please replace the SoBs with RBs.


Rob.

On Sun, 18 Oct 2020 at 14:52, <kholk11@xxxxxxxxx> wrote:
>
> From: AngeloGioacchino Del Regno <kholk11@xxxxxxxxx>
>
> This patch series implements support for the entire camera subsystem
> found in SDM630/636/660 and SDA variants, including CSIPHY 3-Phase,
> CSID v5.0, ISPIF 3.0 (though it didn't need any adaptation) and
> VFE 4.8.
>
> One small note about VFE4.8, even if I wrote it in the commit that
> adds support for it: I know, the VFE support here is split in
> multiple files having the name of the actual VFE version that it is
> targeting... but it didn't feel right to commonize the VFE 4.7 file
> and make another one only for VFE4.8, when it's just about something
> like 3 small differences.
> That VFE 4.8 seems to be just a minor revision of VFE 4.7.
>
> While at it, also fix a small issue when using two VFEs: only one
> of them was being resetted (always VFE0) so, after the first usage
> of VFE1, in case we leave it in a bad state, it would not properly
> start again. Now... it's fine :)))
>
> P.S.: SDM630/660's camss seems to be *very* similar to MSM8998, so
>       likely 90% of this series should be reusable on that one, too!
>
> Tested on:
>  - Sony Xperia XA2 (IMX300 on CSI0/PHY0/VFE0, IMX219 on CSI2,PHY2,VFE1)
>    * VFE0/1 RDI only, as the VIDEO one does not work with SRGGB Bayer
>      formats yet. As far as I can see, that color format hasn't been
>      implemented yet in the video interface.
>
> AngeloGioacchino Del Regno (6):
>   media: camss: csiphy-3ph: Add support for SDM630/660
>   media: camss: ispif: Correctly reset based on the VFE ID
>   media: camss: vfe: Add support for VFE 4.8
>   media: camss: Add support for SDM630/636/660 camera subsystem
>   media: dt-bindings: media: qcom,camss: Add bindings for SDM660 camss
>   media: camss: csiphy: Set rate on csiX_phy clock on SDM630/660
>
>  .../devicetree/bindings/media/qcom,camss.txt  |   7 +
>  .../media/platform/qcom/camss/camss-csid.c    |   9 +-
>  .../qcom/camss/camss-csiphy-3ph-1-0.c         |   7 +-
>  .../media/platform/qcom/camss/camss-csiphy.c  |  25 ++-
>  .../media/platform/qcom/camss/camss-csiphy.h  |   1 +
>  .../media/platform/qcom/camss/camss-ispif.c   | 100 ++++++---
>  .../media/platform/qcom/camss/camss-ispif.h   |   2 +-
>  .../media/platform/qcom/camss/camss-vfe-4-7.c | 129 ++++++++++-
>  drivers/media/platform/qcom/camss/camss-vfe.c |  19 +-
>  drivers/media/platform/qcom/camss/camss-vfe.h |   1 +
>  .../media/platform/qcom/camss/camss-video.c   |   3 +-
>  drivers/media/platform/qcom/camss/camss.c     | 206 +++++++++++++++++-
>  drivers/media/platform/qcom/camss/camss.h     |   1 +
>  13 files changed, 448 insertions(+), 62 deletions(-)
>
> --
> 2.28.0
>