Hi Michael,
-----Original Message-----
From: Michael Grzeschik <mgr@xxxxxxxxxxxxxx>
Sent: Tuesday, February 9, 2021 5:26 AM
To: Manish Narani <MNARANI@xxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx; p.zabel@xxxxxxxxxxxxxx; balbi@xxxxxxxxxx;
gregkh@xxxxxxxxxxxxxxxxxxx; linux-usb@xxxxxxxxxxxxxxx; linux-
kernel@xxxxxxxxxxxxxxx; robh+dt@xxxxxxxxxx; Michal Simek
<michals@xxxxxxxxxx>; git <git@xxxxxxxxxx>; kernel@xxxxxxxxxxxxxx; linux-
arm-kernel@xxxxxxxxxxxxxxxxxxx
Subject: Re: [RESEND PATCH v3 2/2] usb: dwc3: Add driver for Xilinx
platforms
Hi Manish!
On Thu, Jan 28, 2021 at 12:36:07AM +0100, Michael Grzeschik wrote:
>On Fri, Jan 22, 2021 at 02:34:52PM +0100, Michael Grzeschik wrote:
>>On Fri, Jan 22, 2021 at 01:06:22PM +0000, Manish Narani wrote:
>>>Hi Michael,
>>>
>>>>-----Original Message-----
>>>>From: Michael Grzeschik <mgr@xxxxxxxxxxxxxx>
>>>>Sent: Friday, January 22, 2021 1:39 PM
>>>>To: Manish Narani <MNARANI@xxxxxxxxxx>
>>>>Cc: devicetree@xxxxxxxxxxxxxxx; kernel@xxxxxxxxxxxxxx;
balbi@xxxxxxxxxx;
>>>>gregkh@xxxxxxxxxxxxxxxxxxx; linux-usb@xxxxxxxxxxxxxxx; Michal Simek
>>>><michals@xxxxxxxxxx>; linux-kernel@xxxxxxxxxxxxxxx;
robh+dt@xxxxxxxxxx;
>>>>git <git@xxxxxxxxxx>; p.zabel@xxxxxxxxxxxxxx; linux-arm-
>>>>kernel@xxxxxxxxxxxxxxxxxxx
>>>>Subject: Re: [RESEND PATCH v3 2/2] usb: dwc3: Add driver for Xilinx
>>>>platforms
>>>>
>>>>Hello!
>>>>
>>>>On Mon, Jan 18, 2021 at 02:42:24PM +0100, Michael Grzeschik wrote:
>>>>>Hi!
>>>>>
>>>>>On Tue, Dec 15, 2020 at 12:24:51PM +0530, Manish Narani wrote:
>>>>>>Add a new driver for supporting Xilinx platforms. This driver is used
>>>>>>for some sequence of operations required for Xilinx USB controllers.
>>>>>>This driver is also used to choose between PIPE clock coming from
SerDes
>>>>>>and the Suspend Clock. Before the controller is out of reset, the clock
>>>>>>selection should be changed to PIPE clock in order to make the USB
>>>>>>controller work. There is a register added in Xilinx USB controller
>>>>>>register space for the same.
>>>>>
>>>>>I tried out this driver with the vanilla kernel on an zynqmp. Without
>>>>>this patch the USB-Gadget is already acting buggy. In the gadget mode,
>>>>>some iterations of plug/unplug results to an stalled gadget which will
>>>>>never come back without a reboot.
>>>>>
>>>>>With the corresponding code of this driver (reset assert, clk modify,
>>>>>reset deassert) in the downstream kernels phy driver we found out it is
>>>>>totaly stable. But using this exact glue driver which should do the same
>>>>>as the downstream code, the gadget still was buggy the way described
>>>>>above.
>>>>>
>>>>>I suspect the difference lays in the different order of operations.
>>>>>While the downstream code is runing the resets inside the phy driver
>>>>>which is powered and initialized in the dwc3-core itself. With this glue
>>>>>layser approach of this patch the whole phy init is done before even
>>>>>touching dwc3-core in any way. It seems not to have the same effect,
>>>>>though.
>>>>>
>>>>>If really the order of operations is limiting us, we probably need
>>>>>another solution than this glue layer. Any Ideas?
>>>>
>>>>I found out what the difference between the Downstream and this
>>>>Glue is. When using vanilla with this Glue code we may not set
>>>>the following bit:
>>>>
>>>>https://www.xilinx.com/html_docs/registers/ug1087/ug1087-zynq-
>>>>ultrascale-registers.html#usb3_regs___fpd_power_prsnt.html
>>>>
>>>>>>+ /* Set PIPE Power Present signal in FPD Power Present
Register*/
>>>>>>+ writel(PIPE_POWER_ON, priv_data->regs +
>>>>XLNX_USB_FPD_POWER_PRSNT);
>>>>
>>>>When I comment this out, the link stays stable. This is different in
>>>>the Downstream Xilinx Kernel, where the bit is also set but has no
>>>>negativ effect.
>>>>
>>>>Manish, can you give me a pointer what to look for?
>>>>So setting this will also work with mainline?
>>>I am looking further on this but from what I see here is that,
>>>In order to make USB function properly, there are some dt changes
needed in mainline for
>>>USB node which include defining clocks coming from serdes.
>>>The DT changes are pending to be sent to mainline.
>>
>>Can you push that state somewhere, so I could test it?
>>Or is in the downstream kernel some things to copy?
>>
>>>Can you share the DT settings for USB node on your side?
>>
>>Here is my current configuration for the device node at usb0:
>>
>>zynqmp.dtsi
>>
>>zynqmp_reset: reset-controller {
>> compatible = "xlnx,zynqmp-reset";
>> #reset-cells = <1>;
>>};
>>
>>usb0: usb@ff9d0000 {
>> #address-cells = <2>;
>> #size-cells = <2>;
>> status = "disabled";
>> compatible = "xlnx,zynqmp-dwc3";
>> reg = <0x0 0xff9d0000 0x0 0x100>;
>> clock-names = "bus_clk", "ref_clk";
>> power-domains = <&zynqmp_firmware PD_USB_0>;
>> ranges;
>> resets = <&zynqmp_reset ZYNQMP_RESET_USB0_CORERESET>,
>> <&zynqmp_reset ZYNQMP_RESET_USB0_HIBERRESET>,
>> <&zynqmp_reset ZYNQMP_RESET_USB0_APB>;
>> reset-names = "usb_crst", "usb_hibrst", "usb_apbrst";
>> phy-names = "usb3-phy";
>> phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
>>
>> usb0_dwc3: dwc3@fe200000 {
>> compatible = "snps,dwc3";
>> interrupt-parent = <&gic>;
>> interrupts = <0 65 4>;
>> clock-names = "ref", "bus_early", "suspend";
>> reg = <0x0 0xfe200000 0x0 0x40000>;
>> };
>>};
>>
>>platform.dts
>>
>>&usb0 {
>> status = "okay";
>> phy-names = "usb3-phy";
>> phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
>>};
>>
>>&usb0_dwc3 {
>> dr_mode = "peripheral";
>>
>> /* The following quirks are required, since the bInterval is 1 and we
>> * handle steady ISOC streaming. See Usecase 3 in commit
729dcffd1ed3
>> * ("usb: dwc3: gadget: Add support for disabling U1 and U2
entries").
>> */
>> snps,dis-u1-entry-quirk;
>> snps,dis-u2-entry-quirk;
>>};
>>
>>
>>>Meanwhile I will keep updating on the same.
>>
>>Thanks, that sounds great!
>
>I have more feedback regarding this issues. As we saw new uncommon
>effects, when using the glue. Regarding to get the plug/unplug behaviour
>stable, we sticked with leaving out the setting of PIPE_POWER_ON in that
>driver. Unfortunately, with that change, the dwc3 is not only not
>sending any Erratic Errors any more, but also is lacking to send
>disconnect interrupts.
>
>Double checking with downstream shows that disconnects are working
>completely fine in your downstream stack.
>
>I think we should really need to know why PIPE_POWER_ON is making
>a difference before we can say the dwc3 is stable with that glue.
After bisecting your v5.4 and mainline we found out that this all is
working fine, when setting "snps,dis_u3_susphy_quirk" in the zynqmp.dtsi
dwc3 node.
The code handling this quirk was introduced after v5.4, so this was
never an issue with your downstream stack.
"9ba3aca8 usb: dwc3: Disable phy suspend after power-on reset"
We need to know if adding snps,dis_u3_susphy_quirk to the dwc nodes
is generally necessary for zynqmp, so we can fix for everyone.
Yes, it is necessary for DWC3 on ZynqMP platform. This property should be
added to the DT node.
Attachment:
signature.asc
Description: PGP signature