Hi Manish,
On Tue, Feb 09, 2021 at 06:01:58AM +0000, Manish Narani wrote:
Hi Michael,
-----Original Message-----
From: Michael Grzeschik <mgr@xxxxxxxxxxxxxx>
Sent: Tuesday, February 9, 2021 5:26 AM
To: Manish Narani <MNARANI@xxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx; p.zabel@xxxxxxxxxxxxxx; balbi@xxxxxxxxxx;
gregkh@xxxxxxxxxxxxxxxxxxx; linux-usb@xxxxxxxxxxxxxxx; linux-
kernel@xxxxxxxxxxxxxxx; robh+dt@xxxxxxxxxx; Michal Simek
<michals@xxxxxxxxxx>; git <git@xxxxxxxxxx>; kernel@xxxxxxxxxxxxxx; linux-
arm-kernel@xxxxxxxxxxxxxxxxxxx
Subject: Re: [RESEND PATCH v3 2/2] usb: dwc3: Add driver for Xilinx
platforms
Hi Manish!
On Thu, Jan 28, 2021 at 12:36:07AM +0100, Michael Grzeschik wrote:
On Fri, Jan 22, 2021 at 02:34:52PM +0100, Michael Grzeschik wrote:balbi@xxxxxxxxxx;
On Fri, Jan 22, 2021 at 01:06:22PM +0000, Manish Narani wrote:
Hi Michael,
-----Original Message-----
From: Michael Grzeschik <mgr@xxxxxxxxxxxxxx>
Sent: Friday, January 22, 2021 1:39 PM
To: Manish Narani <MNARANI@xxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx; kernel@xxxxxxxxxxxxxx;
robh+dt@xxxxxxxxxx;gregkh@xxxxxxxxxxxxxxxxxxx; linux-usb@xxxxxxxxxxxxxxx; Michal Simek
<michals@xxxxxxxxxx>; linux-kernel@xxxxxxxxxxxxxxx;
SerDesgit <git@xxxxxxxxxx>; p.zabel@xxxxxxxxxxxxxx; linux-arm-
kernel@xxxxxxxxxxxxxxxxxxx
Subject: Re: [RESEND PATCH v3 2/2] usb: dwc3: Add driver for Xilinx
platforms
Hello!
On Mon, Jan 18, 2021 at 02:42:24PM +0100, Michael Grzeschik wrote:
Hi!
On Tue, Dec 15, 2020 at 12:24:51PM +0530, Manish Narani wrote:
Add a new driver for supporting Xilinx platforms. This driver is used
for some sequence of operations required for Xilinx USB controllers.
This driver is also used to choose between PIPE clock coming from
Register*/and the Suspend Clock. Before the controller is out of reset, the clock
selection should be changed to PIPE clock in order to make the USB
controller work. There is a register added in Xilinx USB controller
register space for the same.
I tried out this driver with the vanilla kernel on an zynqmp. Without
this patch the USB-Gadget is already acting buggy. In the gadget mode,
some iterations of plug/unplug results to an stalled gadget which will
never come back without a reboot.
With the corresponding code of this driver (reset assert, clk modify,
reset deassert) in the downstream kernels phy driver we found out it is
totaly stable. But using this exact glue driver which should do the same
as the downstream code, the gadget still was buggy the way described
above.
I suspect the difference lays in the different order of operations.
While the downstream code is runing the resets inside the phy driver
which is powered and initialized in the dwc3-core itself. With this glue
layser approach of this patch the whole phy init is done before even
touching dwc3-core in any way. It seems not to have the same effect,
though.
If really the order of operations is limiting us, we probably need
another solution than this glue layer. Any Ideas?
I found out what the difference between the Downstream and this
Glue is. When using vanilla with this Glue code we may not set
the following bit:
https://www.xilinx.com/html_docs/registers/ug1087/ug1087-zynq-
ultrascale-registers.html#usb3_regs___fpd_power_prsnt.html
+ /* Set PIPE Power Present signal in FPD Power Present
needed in mainline forI am looking further on this but from what I see here is that,XLNX_USB_FPD_POWER_PRSNT);+ writel(PIPE_POWER_ON, priv_data->regs +
When I comment this out, the link stays stable. This is different in
the Downstream Xilinx Kernel, where the bit is also set but has no
negativ effect.
Manish, can you give me a pointer what to look for?
So setting this will also work with mainline?
In order to make USB function properly, there are some dt changes
729dcffd1ed3USB node which include defining clocks coming from serdes.
The DT changes are pending to be sent to mainline.
Can you push that state somewhere, so I could test it?
Or is in the downstream kernel some things to copy?
Can you share the DT settings for USB node on your side?
Here is my current configuration for the device node at usb0:
zynqmp.dtsi
zynqmp_reset: reset-controller {
compatible = "xlnx,zynqmp-reset";
#reset-cells = <1>;
};
usb0: usb@ff9d0000 {
#address-cells = <2>;
#size-cells = <2>;
status = "disabled";
compatible = "xlnx,zynqmp-dwc3";
reg = <0x0 0xff9d0000 0x0 0x100>;
clock-names = "bus_clk", "ref_clk";
power-domains = <&zynqmp_firmware PD_USB_0>;
ranges;
resets = <&zynqmp_reset ZYNQMP_RESET_USB0_CORERESET>,
<&zynqmp_reset ZYNQMP_RESET_USB0_HIBERRESET>,
<&zynqmp_reset ZYNQMP_RESET_USB0_APB>;
reset-names = "usb_crst", "usb_hibrst", "usb_apbrst";
phy-names = "usb3-phy";
phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
usb0_dwc3: dwc3@fe200000 {
compatible = "snps,dwc3";
interrupt-parent = <&gic>;
interrupts = <0 65 4>;
clock-names = "ref", "bus_early", "suspend";
reg = <0x0 0xfe200000 0x0 0x40000>;
};
};
platform.dts
&usb0 {
status = "okay";
phy-names = "usb3-phy";
phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&usb0_dwc3 {
dr_mode = "peripheral";
/* The following quirks are required, since the bInterval is 1 and we
* handle steady ISOC streaming. See Usecase 3 in commit
entries").* ("usb: dwc3: gadget: Add support for disabling U1 and U2
*/
snps,dis-u1-entry-quirk;
snps,dis-u2-entry-quirk;
};
Meanwhile I will keep updating on the same.
Thanks, that sounds great!
I have more feedback regarding this issues. As we saw new uncommon
effects, when using the glue. Regarding to get the plug/unplug behaviour
stable, we sticked with leaving out the setting of PIPE_POWER_ON in that
driver. Unfortunately, with that change, the dwc3 is not only not
sending any Erratic Errors any more, but also is lacking to send
disconnect interrupts.
Double checking with downstream shows that disconnects are working
completely fine in your downstream stack.
I think we should really need to know why PIPE_POWER_ON is making
a difference before we can say the dwc3 is stable with that glue.
After bisecting your v5.4 and mainline we found out that this all is
working fine, when setting "snps,dis_u3_susphy_quirk" in the zynqmp.dtsi
dwc3 node.
The code handling this quirk was introduced after v5.4, so this was
never an issue with your downstream stack.
"9ba3aca8 usb: dwc3: Disable phy suspend after power-on reset"
We need to know if adding snps,dis_u3_susphy_quirk to the dwc nodes
is generally necessary for zynqmp, so we can fix for everyone.
Yes, it is necessary for DWC3 on ZynqMP platform. This property should be
added to the DT node.
For now this quirk does solve the issues regarding the pluging
behaviour. But we would like to know why?
Is the phy not properly configured/connected to serve the phy
suspend as intended for the dwc3 stack? Is this a real Hardware issue,
or does this quirk only disable the suspend behaviour even though it
would work properly when configured correctly in software.
The second question is addressing the dwc3 xilinx glue driver
you are trying to mainline. We found that the driver is pulling and
releasing some resets before and after changing the pll frequency
comming from the reference clk lines. After that the undocumented
registers XLNX_USB_FPD_POWER_PRSNT and XLNX_USB_FPD_PIPE_CLK are changed
according to the updated pll frequency. What do these bit change?
Is this an internal configuration every dwc3 user on the zynqmp has
to do or does this differ from user to user?
Regards,
Michael
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Attachment:
signature.asc
Description: PGP signature