[PATCH AUTOSEL 5.10 108/176] ARM: tegra: acer-a500: Remove bogus USB VBUS regulators

[Sasha Levin]

From: Dmitry Osipenko <digetx@xxxxxxxxx>

[ Upstream commit 70e740ad55e5f93a19493720f4105555fade4a73 ]

The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.

Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
Signed-off-by: Thierry Reding <treding@xxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
 .../boot/dts/tegra20-acer-a500-picasso.dts    | 25 +------------------
 1 file changed, 1 insertion(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts b/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts
index 5d0f0fbba1d2..5dbfb83c1b06 100644
--- a/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts
+++ b/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts
@@ -704,7 +704,6 @@ usb-phy@c5000000 {
 		nvidia,xcvr-setup-use-fuses;
 		nvidia,xcvr-lsfslew = <2>;
 		nvidia,xcvr-lsrslew = <2>;
-		vbus-supply = <&vdd_vbus1>;
 	};
 
 	usb@c5008000 {
@@ -716,7 +715,7 @@ usb-phy@c5008000 {
 		nvidia,xcvr-setup-use-fuses;
 		nvidia,xcvr-lsfslew = <2>;
 		nvidia,xcvr-lsrslew = <2>;
-		vbus-supply = <&vdd_vbus3>;
+		vbus-supply = <&vdd_5v0_sys>;
 	};
 
 	brcm_wifi_pwrseq: wifi-pwrseq {
@@ -967,28 +966,6 @@ vdd_pnl: regulator@3 {
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_vbus1: regulator@4 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_usb1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-		gpio = <&gpio TEGRA_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		vin-supply = <&vdd_5v0_sys>;
-	};
-
-	vdd_vbus3: regulator@5 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_usb3_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-		gpio = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		vin-supply = <&vdd_5v0_sys>;
-	};
-
 	sound {
 		compatible = "nvidia,tegra-audio-wm8903-picasso",
 			     "nvidia,tegra-audio-wm8903";
-- 
2.30.2