RE: [PATCH] usb: chipidea: udc: make controller hardware endpoint primed

[Piyush Mehta]

Hello Peter,

Thanks for the review.
Please find my inline comment with tag [Piyush].

Regards,
Piyush Mehta

-----Original Message-----
From: Peter Chen <peter.chen@xxxxxxxxxx> 
Sent: Sunday, September 12, 2021 1:11 PM
To: Piyush Mehta <piyushm@xxxxxxxxxx>
Cc: gregkh@xxxxxxxxxxxxxxxxxxx; linux-usb@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; git <git@xxxxxxxxxx>; Srinivas Goud <sgoud@xxxxxxxxxx>; Michal Simek <michals@xxxxxxxxxx>
Subject: Re: [PATCH] usb: chipidea: udc: make controller hardware endpoint primed

On 21-09-08 14:13:21, Piyush Mehta wrote:
> Root-cause:
> There is an issue like endpoint is not recognized as primed, when bus 
> have more pressure and the add dTD tripwire semaphore (ATDTW bit in 
> USBCMD register) that can cause the controller to ignore a dTD that is 
> added to a primed endpoint.
> This issue observed with the Windows10 host machine.
> 
> Workaround:
> The software must implement a periodic cycle, and check for each dTD, 
> if the endpoint is primed. It can do this by reading the corresponding 
> bits in the ENDPTPRIME and ENDPTSTAT registers. If these bits are read 
> at 0, the software needs to re-prime the endpoint by writing 1 to the 
> corresponding bit in the ENDPTPRIME register.
> 
> Signed-off-by: Piyush Mehta <piyush.mehta@xxxxxxxxxx>
> ---
>  drivers/usb/chipidea/udc.c | 9 +++++++++
>  1 file changed, 9 insertions(+)
> 
> diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c 
> index 8834ca6..d970f45 100644
> --- a/drivers/usb/chipidea/udc.c
> +++ b/drivers/usb/chipidea/udc.c
> @@ -49,6 +49,8 @@ ctrl_endpt_in_desc = {
>  	.wMaxPacketSize  = cpu_to_le16(CTRL_PAYLOAD_MAX),  };
>  
> +static int reprime_dtd(struct ci_hdrc *ci, struct ci_hw_ep *hwep,
> +		       struct td_node *node);
>  /**
>   * hw_ep_bit: calculates the bit number
>   * @num: endpoint number
> @@ -599,8 +601,15 @@ static int _hardware_enqueue(struct ci_hw_ep 
> *hwep, struct ci_hw_req *hwreq)
>  
>  		prevlastnode->ptr->next = cpu_to_le32(next);
>  		wmb();
> +
> +		if (ci->rev == CI_REVISION_22) {
> +			if (!hw_read(ci, OP_ENDPTSTAT, BIT(n)))
> +				reprime_dtd(ci, hwep, prevlastnode);
> +		}
> +

Only for version 2.2?
[Piyush]
Yes, Xilinx chip-idea controller support revision 2.20 only.
This solution is validated on revision 2.20 on the zynq7000 platform.

>  		if (hw_read(ci, OP_ENDPTPRIME, BIT(n)))
>  			goto done;
> +

No blank line.

>  		do {
>  			hw_write(ci, OP_USBCMD, USBCMD_ATDTW, USBCMD_ATDTW);
>  			tmp_stat = hw_read(ci, OP_ENDPTSTAT, BIT(n));
> --
> 2.7.4
> 

-- 

Thanks,
Peter Chen