Re: [PATCH v2 1/2] watchdog: Add watchdog driver for Sunplus SP7021

[Guenter Roeck]

On 11/24/21 6:42 PM, xt.hu[胡先韬] wrote:
> Hi
> 	Thanks for your review. I explain this in detail below the comment.
>
> Best Regards,
> Xiantao
> > -----Original Message-----
> > From: Guenter Roeck [mailto:groeck7@xxxxxxxxx] On Behalf Of Guenter Roeck
> > Sent: Wednesday, November 24, 2021 10:25 PM
> > To: xt.hu[胡先韬] <xt.hu@xxxxxxxxxxx>
> > Cc: wim@xxxxxxxxxxxxxxxxxx; p.zabel@xxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> > linux-watchdog@xxxxxxxxxxxxxxx; robh+dt@xxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; Wells Lu 呂芳騰
> > <wells.lu@xxxxxxxxxxx>; qinjian[覃健] <qinjian@xxxxxxxxxxx>
> > Subject: Re: [PATCH v2 1/2] watchdog: Add watchdog driver for Sunplus SP7021
> >
> > On Wed, Nov 24, 2021 at 06:41:48PM +0800, Xiantao Hu wrote:
> > > Sunplus SP7021 requires watchdog timer support.
> > > Add watchdog driver to enable this.
> > >
> > > Signed-off-by: Xiantao Hu <xt.hu@xxxxxxxxxxx>
> > > ---
> > > +
> > > +	priv->base = devm_platform_ioremap_resource(pdev, 0);
> > > +	if (IS_ERR(priv->base))
> > > +		return PTR_ERR(priv->base);
> > > +
> > > +	/* The registers accessed here shared by multiple drivers. */
> > > +	wdt_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> >
> > This is unusual. Why would other drivers access WDT_CTRL and WDT_CNT registers, and how is it
> > ensured that the other drivers do not interfer with the accesses by this driver ?
> >
> > Normally such a resource would be shared through a parent driver with appropriate access functions to
> > ensure that accesses are synchronized.
>
> The register used by this driver consists of two parts. The first part which contains WDT_CTRL and WDT_CNT
> registers is exclusive by watchdog.
> In specially, the second part is belong to a multifunctional register group which control IP and bus. Refer to
> register manual below:
> -------------------------------------------------------------------------------------------------------------------------------------------------
> MO1_STC_WDG_RST_EN	4	RW		STC Watchdog Timeout Trigger System Reset Enable
> 									0: STC watchdog 2 timeout will not trigger system reset(default)
> 									1: STC watchdog 2 timeout will trigger system reset
> MO1_RI_WDG_RST_EN		1	RW		RBUS Watchdog Timeout Trigger System Reset Enable
> 									0: RBUS watchdog timeout will not trigger system reset(default)
> 									1: RBUS watchdog timeout will trigger system reset
> MO1_TIMER_STAND_BY_EN	0	RW		Timer Standby Mode Enable
> 									0: Disable (default)
> 									1: Enable Active high to enter timer standby mode,
> 											default not in standby mode
> -------------------------------------------------------------------------------------------------------------------------------------------------
> You can see that in addition to the bits for watchdog there are bit fields for other modules.
> I use this register bit4 and bit1. Default value is 0 that watchdog internal interrupt signal can't trigger system
> and RBUS reset. I need set 1 when watchdog probe. Early I implement the operation in
> arch/arm/mach-sunplus/sp7021.c and configure by macro. But in arch/arm64, directory mach-XXX is removed.
> So I solve in this way. Any better way?
If the register at 0x9C000274 is accessed by other drivers, accesses
to it must be protected against each other to avoid race conditions.
How to do that would be up to you.

Guenter