Re: linux-next: build warnings after merge of the hwmon-staging tree

[Guenter Roeck]

On 6/7/22 02:37, Bagas Sanjaya wrote:
> On Tue, Jun 07, 2022 at 02:19:58PM +1000, Stephen Rothwell wrote:
> > Hi all,
> >
> > After merging the hwmon-staging tree, today's linux-next build (htmldocs)
> > produced these warnings:
> >
> > Documentation/hwmon/lt7182s.rst:2: WARNING: Explicit markup ends without a blank line; unexpected unindent.
> > Documentation/hwmon/lt7182s.rst:75: WARNING: Malformed table.
> > Text in column margin in table line 33.
> >
> > ======================  ====================================
> > curr[1-2]_label         "iin[12]"
> > curr[1-2]_input         Measured input current
> > curr[1-2]_max           Maximum input current
> > curr[1-2]_max_alarm     Current high alarm
> >
> > curr[3-4]_label         "iout[1-2]"
> > curr[3-4]_input         Measured output current
> > curr[3-4]_highest       Highest measured output current
> > curr[3-4]_max           Maximum output current
> > curr[3-4]_max_alarm     Output current high alarm
> >
> > in[1-2]_label           "vin[12]"
> > in[1-2]_input           Measured input voltage
> > in[1-2]_highest         Highest measured input voltage
> > in[1-2]_crit            Critical maximum input voltage
> > in[1-2]_crit_alarm      Input voltage critical high alarm
> > in[1-2]_min             Minimum input voltage
> > in[1-2]_min_alarm       Input voltage low alarm
> > in[1-2]_rated_min       Rated minimum input voltage
> > in[1-2]_rated_max       Rated maximum input voltage
> > in1_reset_history       Write to reset history for all attributes
> >
> > in[3-5]_label           "vmon[1-3]"
> > in[3-5]_input           Measured voltage on ITH1/ITH2/EXTVCC pins
> >                          Only available if enabled with MFR_ADC_CONTROL_LT7182S
> >                          command.
> >
> > in[3-4|6-7]_label       "vout[1-2]"
> > in[3-4|6-7]_input       Measured output voltage
> > in[3-4|6-7]_highest     Highest measured output voltage
> > in[3-4|6-7]_lcrit       Critical minimum output voltage
> > in[3-4|6-7]_lcrit_alarm Output voltage critical low alarm
                         ^
> > in[3-4|6-7]_min         Minimum output voltage
> > in[3-4|6-7]_max_alarm   Output voltage low alarm
> > in[3-4|6-7]_max         Maximum output voltage
> > in[3-4|6-7]_max_alarm   Output voltage high alarm
> > in[3-4|6-7]_crit        Critical maximum output voltage
> > in[3-4|6-7]_crit_alarm  Output voltage critical high alarm
> >
> > power[1-2]_label        "pout[1-2]"
> > power[1-2]_input        Measured output power
> >
> > temp1_input             Measured temperature
> > temp1_crit              Critical high temperature
> > temp1_crit_alarm        Chip temperature critical high alarm
> > temp1_max               Maximum temperature
> > temp1_max_alarm         Chip temperature high alarm
> > ======================  ====================================
> >
> > Introduced by commit
> >
> >    3d6bcaa21fbd ("hwmon: (pmbus) Add support for Analog Devices LT7182S")
>
> Hi Stephen,
>
> The warning above doesn't appear when doing htmldocs build using Sphinx
> installed from pip on my system.

I already fixed it up.

Guenter