Re: [PATCH 11/12] ASoC: cs42l42: Add Soundwire support
From: Richard Fitzgerald
Date: Mon Aug 22 2022 - 09:51:00 EST
On 22/08/2022 12:15, Pierre-Louis Bossart wrote:
Thanks Richard, this looks quite good.
Nit-pick for the entire patch: SoundWire (capital W).
- Intel Soundwire host controllers have a low-power clock-stop mode that
requires resetting all peripherals when resuming. This is not compatible
with the plug-detect and button-detect because it will clear the
condition that caused the wakeup before the driver can handle it. So
clock-stop must be blocked when a snd_soc_jack handler is registered.
What do you mean by 'clock-stop must be blocked'? The peripheral cannot
prevent the host from stopping the clock.
Are you sure about that? We're going to have serious problems if the
Intel manager driver can clock-stop even though there are peripheral
drivers still using the clock.
Currently the Intel code will only clock-stop when it goes into
runtime suspend, which only happens if all peripheral drivers are also
in runtime suspend. Or on system suspend, which is handled specially by
the cs42l42 driver. If you are saying this isn't guaranteed behavior
then we'll need to add something to the core Soundwire core code to tell
it when it's allowed to clock-stop.
I tried returning an error from the codec driver clk_stop() callback but
the core code and cadence code treat that as unexpected and dev_err()
it, then the intel.c code ignores the error and carries on suspending.
Maybe this is explained
further down in this patch, but that statement is a bit odd.
Even if the condition that caused the wakeup was cleared, presumably
when resetting the device the same condition will be raised again, no?
+static int cs42l42_sdw_dai_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params,
+ struct snd_soc_dai *dai)
+{
+ struct cs42l42_private *cs42l42 = snd_soc_component_get_drvdata(dai->component);
+ struct sdw_stream_runtime *sdw_stream = snd_soc_dai_get_dma_data(dai, substream);
+ struct sdw_stream_config sconfig;
+ struct sdw_port_config pconfig;
+ unsigned int pdn_mask;
+ int ret;
+
+ if (!sdw_stream)
+ return -EINVAL;
+
+ /* Needed for PLL configuration when we are notified of new bus config */
+ cs42l42->sample_rate = params_rate(params);
+
+ memset(&sconfig, 0, sizeof(sconfig));
+ memset(&pconfig, 0, sizeof(pconfig));
+
+ sconfig.frame_rate = params_rate(params);
+ sconfig.ch_count = params_channels(params);
+ sconfig.bps = snd_pcm_format_width(params_format(params));
+ pconfig.ch_mask = GENMASK(sconfig.ch_count - 1, 0);
+
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
+ sconfig.direction = SDW_DATA_DIR_RX;
+ pconfig.num = CS42L42_SDW_PLAYBACK_PORT;
+ pdn_mask = CS42L42_HP_PDN_MASK;
+ } else {
+ sconfig.direction = SDW_DATA_DIR_TX;
+ pconfig.num = CS42L42_SDW_CAPTURE_PORT;
+ pdn_mask = CS42L42_ADC_PDN_MASK;
+ }
+
+ /*
+ * The DAI-link prepare() will trigger Soundwire DP prepare. But CS42L42
+ * DP will only prepare if the HP/ADC is already powered-up. The
+ * DAI prepare() and DAPM sequence run after DAI-link prepare() so the
+ * PDN bit must be written here.
+ */
Why not make use of the callbacks that were added precisely to let the
codec driver perform device-specific operations? You can add your own
code in pre and post operation for both prepare and bank switch. It's
not clear why you would do this in a hw_params (which can be called
multiple times per ALSA conventions).
Ah, I'd not noticed the port_prep callback. Maybe it didn't exist when
this code was first written.
+ regmap_clear_bits(cs42l42->regmap, CS42L42_PWR_CTL1, pdn_mask);
+ usleep_range(CS42L42_HP_ADC_EN_TIME_US, CS42L42_HP_ADC_EN_TIME_US + 1000);
+
+ ret = sdw_stream_add_slave(cs42l42->sdw_peripheral, &sconfig, &pconfig, 1, sdw_stream);
+ if (ret) {
+ dev_err(dai->dev, "Failed to add sdw stream: %d\n", ret);
+ goto err;
+ }
+
+ cs42l42_src_config(dai->component, params_rate(params));
+
+ return 0;
+
+err:
+ regmap_set_bits(cs42l42->regmap, CS42L42_PWR_CTL1, pdn_mask);
+
+ return ret;
+}
+
+static int cs42l42_sdw_dai_prepare(struct snd_pcm_substream *substream,
+ struct snd_soc_dai *dai)
+{
+ struct cs42l42_private *cs42l42 = snd_soc_component_get_drvdata(dai->component);
+
+ dev_dbg(dai->dev, "dai_prepare: sclk=%u rate=%u\n", cs42l42->sclk, cs42l42->sample_rate);
+
+ if (!cs42l42->sclk || !cs42l42->sample_rate)
what does sclk mean in the SoundWire context?
+ return -EINVAL;
+
+ return cs42l42_pll_config(dai->component, cs42l42->sclk, cs42l42->sample_rate);
+}
+
There should be a really big comment here that the following functions
implement delayed reads and writes - this was not needed for previous
codecs.
+static int cs42l42_sdw_poll_status(struct sdw_slave *peripheral, u8 mask, u8 match)
+{
+ int ret, sdwret;
+
+ ret = read_poll_timeout(sdw_read_no_pm, sdwret,
+ (sdwret < 0) || ((sdwret & mask) == match),
+ CS42L42_DELAYED_READ_POLL_US, CS42L42_DELAYED_READ_TIMEOUT_US,
+ false, peripheral, CS42L42_SDW_MEM_ACCESS_STATUS);
+ if (ret == 0)
+ ret = sdwret;
+
+ if (ret < 0)
+ dev_err(&peripheral->dev, "MEM_ACCESS_STATUS & %#x for %#x fail: %d\n",
+ mask, match, ret);
+
+ return ret;
+}
+
+static int cs42l42_sdw_read(void *context, unsigned int reg, unsigned int *val)
+{
+ struct sdw_slave *peripheral = context;
+ u8 data;
+ int ret;
+
+ reg += CS42L42_SDW_ADDR_OFFSET;
+
+ ret = cs42l42_sdw_poll_status(peripheral, CS42L42_SDW_CMD_IN_PROGRESS, 0);
+ if (ret < 0)
+ return ret;
+
+ ret = sdw_read_no_pm(peripheral, reg);
+ if (ret < 0) {
+ dev_err(&peripheral->dev, "Failed to issue read @0x%x: %d\n", reg, ret);
+ return ret;
+ }
+
+ data = (u8)ret; /* possible non-delayed read value */
+ ret = sdw_read_no_pm(peripheral, CS42L42_SDW_MEM_ACCESS_STATUS);
+ if (ret < 0) {
+ dev_err(&peripheral->dev, "Failed to read MEM_ACCESS_STATUS: %d\n", ret);
+ return ret;
+ }
+
+ /* If read was not delayed we already have the result */
+ if ((ret & CS42L42_SDW_LAST_LATE) == 0) {
+ *val = data;
+ return 0;
+ }
+
+ /* Poll for delayed read completion */
+ if ((ret & CS42L42_SDW_RDATA_RDY) == 0) {
+ ret = cs42l42_sdw_poll_status(peripheral,
+ CS42L42_SDW_RDATA_RDY, CS42L42_SDW_RDATA_RDY);
+ if (ret < 0)
+ return ret;
+ }
+
+ ret = sdw_read_no_pm(peripheral, CS42L42_SDW_MEM_READ_DATA);
+ if (ret < 0) {
+ dev_err(&peripheral->dev, "Failed to read READ_DATA: %d\n", ret);
+ return ret;
+ }
+
+ *val = (u8)ret;
+
+ return 0;
+}
+
+static int cs42l42_sdw_write(void *context, unsigned int reg, unsigned int val)
+{
+ struct sdw_slave *peripheral = context;
+ int ret;
+
+ ret = cs42l42_sdw_poll_status(peripheral, CS42L42_SDW_CMD_IN_PROGRESS, 0);
+ if (ret < 0)
+ return ret;
+
+ return sdw_write_no_pm(peripheral, reg + CS42L42_SDW_ADDR_OFFSET, (u8)val);
+}
+
+static void cs42l42_sdw_init(struct sdw_slave *peripheral)
+{
+ struct cs42l42_private *cs42l42 = dev_get_drvdata(&peripheral->dev);
+ int ret = 0;
+
+ regcache_cache_only(cs42l42->regmap, false);
+
+ ret = cs42l42_init(cs42l42);
+ if (ret < 0) {
+ regcache_cache_only(cs42l42->regmap, true);
+ return;
+ }
+
+ /* Write out any cached changes that happened between probe and attach */
+ ret = regcache_sync(cs42l42->regmap);
+ if (ret < 0)
+ dev_warn(cs42l42->dev, "Failed to sync cache: %d\n", ret);
+
+ /* Disable internal logic that makes clock-stop conditional */
+ regmap_clear_bits(cs42l42->regmap, CS42L42_PWR_CTL3, CS42L42_SW_CLK_STP_STAT_SEL_MASK);
+
+ /*
+ * pm_runtime is needed to control bus manager suspend, and to
I don't think the intent is that the codec can control the manager
suspend, but that the manager cannot be suspended by the framework
unless the codec suspends first?
That sounds the same to me. But I can re-word the comment.
+ * recover from an unattach_request when the manager suspends.
+ * Autosuspend delay must be long enough to enumerate.
No, this last sentence is not correct. The enumeration can be done no
matter what pm_runtime state the Linux codec device is in. And it's
really the other way around, it's when the codec reports as ATTACHED
that the codec driver will be resumed.
It can't if the device has powered off. So there has to be some way to
ensure the codec driver won't suspend before the core has completed
enumeration and notified an ATTACH to the codec driver.
+ */
+ pm_runtime_set_autosuspend_delay(cs42l42->dev, 3000);
+ pm_runtime_use_autosuspend(cs42l42->dev);
+ pm_runtime_set_active(cs42l42->dev);
+ pm_runtime_enable(cs42l42->dev);
+ pm_runtime_mark_last_busy(cs42l42->dev);
+ pm_runtime_idle(cs42l42->dev);
+}
+
+static int cs42l42_sdw_read_prop(struct sdw_slave *peripheral)
+{
+ struct cs42l42_private *cs42l42 = dev_get_drvdata(&peripheral->dev);
+ struct sdw_slave_prop *prop = &peripheral->prop;
+ struct sdw_dpn_prop *ports;
+
+ ports = devm_kcalloc(cs42l42->dev, 2, sizeof(*ports), GFP_KERNEL);
+ if (!ports)
+ return -ENOMEM;
+
+ prop->source_ports = BIT(CS42L42_SDW_CAPTURE_PORT);
+ prop->sink_ports = BIT(CS42L42_SDW_PLAYBACK_PORT);
+ prop->quirks = SDW_SLAVE_QUIRKS_INVALID_INITIAL_PARITY;
+ prop->scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY;
+
+ /* DP1 - capture */
+ ports[0].num = CS42L42_SDW_CAPTURE_PORT,
+ ports[0].type = SDW_DPN_FULL,
+ ports[0].ch_prep_timeout = 10,
+ prop->src_dpn_prop = &ports[0];
+
+ /* DP2 - playback */
+ ports[1].num = CS42L42_SDW_PLAYBACK_PORT,
+ ports[1].type = SDW_DPN_FULL,
+ ports[1].ch_prep_timeout = 10,
+ prop->sink_dpn_prop = &ports[1];
+
+ return 0;
+}
+static int cs42l42_sdw_bus_config(struct sdw_slave *peripheral,
+ struct sdw_bus_params *params)
+{
+ struct cs42l42_private *cs42l42 = dev_get_drvdata(&peripheral->dev);
+ unsigned int new_sclk = params->curr_dr_freq / 2;
+
+ /* The cs42l42 cannot support a glitchless SWIRE_CLK change. */
nit-pick: SoundWire
+ if ((new_sclk != cs42l42->sclk) && cs42l42->stream_use) {
+ dev_warn(cs42l42->dev, "Rejected SCLK change while audio active\n");
+ return -EBUSY;
+ }
It's good to have this test but so far we haven't changed the bus clock
on the fly so it's not tested.
+
+ cs42l42->sclk = new_sclk;
+
+ dev_dbg(cs42l42->dev, "bus_config: sclk=%u c=%u r=%u\n",
+ cs42l42->sclk, params->col, params->row);
+
+ return 0;
+}
+
+static int __maybe_unused cs42l42_sdw_clk_stop(struct sdw_slave *peripheral,
+ enum sdw_clk_stop_mode mode,
+ enum sdw_clk_stop_type type)
+{
+ struct cs42l42_private *cs42l42 = dev_get_drvdata(&peripheral->dev);
+
+ dev_dbg(cs42l42->dev, "clk_stop mode:%d type:%d\n", mode, type);
+
+ return 0;
+}
+
+static const struct sdw_slave_ops cs42l42_sdw_ops = {
+ .read_prop = cs42l42_sdw_read_prop,
+ .update_status = cs42l42_sdw_update_status,
+ .bus_config = cs42l42_sdw_bus_config,
+#ifdef DEBUG
+ .clk_stop = cs42l42_sdw_clk_stop,
+#endif
do you really need this wrapper?
+};
+
+static int __maybe_unused cs42l42_sdw_runtime_suspend(struct device *dev)
+{
+ struct cs42l42_private *cs42l42 = dev_get_drvdata(dev);
+
+ dev_dbg(dev, "Runtime suspend\n");
+
+ /* The host controller could suspend, which would mean no register access */
+ regcache_cache_only(cs42l42->regmap, true);
+
+ return 0;
+}
+
+static const struct reg_sequence __maybe_unused cs42l42_soft_reboot_seq[] = {
+ REG_SEQ0(CS42L42_SOFT_RESET_REBOOT, 0x1e),
+};
+static int __maybe_unused cs42l42_sdw_resume(struct device *dev)
+{
+ struct cs42l42_private *cs42l42 = dev_get_drvdata(dev);
+ int ret;
+
+ dev_dbg(dev, "System resume\n");
+
+ /* Power-up so it can re-enumerate */
??
You cannot power-up with the bus, did you mean that side channels are
used for powering up?
+ ret = cs42l42_resume(dev);
+ if (ret)
+ return ret;
+
+ /* Wait for re-attach */
+ ret = cs42l42_sdw_handle_unattach(cs42l42);
+ if (ret < 0)
+ return ret;
+
+ cs42l42_resume_restore(dev);
+
+ return 0;
+}
+
+static int cs42l42_sdw_probe(struct sdw_slave *peripheral, const struct sdw_device_id *id)
+{
+ struct device *dev = &peripheral->dev;
+ struct cs42l42_private *cs42l42;
+ struct regmap_config *regmap_conf;
+ struct regmap *regmap;
+ struct snd_soc_component_driver *component_drv;
+ int irq, ret;
+
+ cs42l42 = devm_kzalloc(dev, sizeof(*cs42l42), GFP_KERNEL);
+ if (!cs42l42)
+ return -ENOMEM;
+
+ if (has_acpi_companion(dev))
+ irq = acpi_dev_gpio_irq_get(ACPI_COMPANION(dev), 0);
+ else
+ irq = of_irq_get(dev->of_node, 0);
why do you need an interrupt when SoundWire provides an in-band one? You
need a lot more explanations on the requirement and what you intend to
do with this interrupt?
+
+ if (irq == -ENOENT)
+ irq = 0;
+ else if (irq < 0)
+ return dev_err_probe(dev, irq, "Failed to get IRQ\n");
+
+ regmap_conf = devm_kmemdup(dev, &cs42l42_regmap, sizeof(cs42l42_regmap), GFP_KERNEL);
+ if (!regmap_conf)
+ return -ENOMEM;
+ regmap_conf->reg_bits = 16;
+ regmap_conf->num_ranges = 0;
+ regmap_conf->reg_read = cs42l42_sdw_read;
+ regmap_conf->reg_write = cs42l42_sdw_write;
+
+ regmap = devm_regmap_init(dev, NULL, peripheral, regmap_conf);
+ if (IS_ERR(regmap))
+ return dev_err_probe(dev, PTR_ERR(regmap), "Failed to allocate register map\n");
+
+ /* Start in cache-only until device is enumerated */
+ regcache_cache_only(regmap, true);
+
+ component_drv = devm_kmemdup(dev,
+ &cs42l42_soc_component,
+ sizeof(cs42l42_soc_component),
+ GFP_KERNEL);
+ if (!component_drv)
+ return -ENOMEM;
+
+ component_drv->dapm_routes = cs42l42_sdw_audio_map;
+ component_drv->num_dapm_routes = ARRAY_SIZE(cs42l42_sdw_audio_map);
+
+ cs42l42->dev = dev;
+ cs42l42->regmap = regmap;
+ cs42l42->sdw_peripheral = peripheral;
+ cs42l42->irq = irq;
+
+ ret = cs42l42_common_probe(cs42l42, component_drv, &cs42l42_sdw_dai);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+static int cs42l42_sdw_remove(struct sdw_slave *peripheral)
+{
+ struct cs42l42_private *cs42l42 = dev_get_drvdata(&peripheral->dev);
+
+ /* Resume so that cs42l42_remove() can access registers */
+ pm_runtime_get_sync(cs42l42->dev);
you need to test if this resume succeeded, and possibly use
pm_resume_resume_and_get() to avoid issues.
+ cs42l42_common_remove(cs42l42);
+ pm_runtime_put(cs42l42->dev);
+ pm_runtime_disable(cs42l42->dev);
+
+ return 0;
+}
static const struct snd_soc_dapm_route cs42l42_audio_map[] = {
@@ -559,6 +564,20 @@ static int cs42l42_set_jack(struct snd_soc_component *component, struct snd_soc_
{
struct cs42l42_private *cs42l42 = snd_soc_component_get_drvdata(component);
+ /*
+ * If the Soundwire controller issues bus reset when coming out of
+ * clock-stop it will erase the jack state. This can lose button press
+ * events, and plug/unplug interrupt bits take between 125ms and 1500ms
+ * before they are valid again.
+ * Prevent this by holding our pm_runtime to block clock-stop.
+ */
+ if (cs42l42->sdw_peripheral) {
+ if (jk)
+ pm_runtime_get_sync(cs42l42->dev);
+ else
+ pm_runtime_put_autosuspend(cs42l42->dev);
+ }
+
I *really* don't understand this sequence.
The bus will be suspended when ALL devices have been idle for some time.
If the user presses a button AFTER the bus is suspended, the device can
still use the in-band wake and resume.
Only if it has that capability. The cs42l42 has very limited wake
capability and cannot wake on interrupt, and it certainly can't accept
the Intel code resetting it before it has a chance to find out what
condition caused the wake.
Granted the button press will be lost but the plug/unplug status will
still be handled with a delay.
I'm finding it difficult to believe it's acceptable to end users for
button events to be lost.
/* Prevent race with interrupt handler */
mutex_lock(&cs42l42->irq_lock);
cs42l42->jack = jk;
@@ -1645,9 +1664,11 @@ irqreturn_t cs42l42_irq_thread(int irq, void *data)
unsigned int current_button_status;
unsigned int i;
+ pm_runtime_get_sync(cs42l42->dev);
mutex_lock(&cs42l42->irq_lock);
if (cs42l42->suspended || !cs42l42->init_done) {
mutex_unlock(&cs42l42->irq_lock);
+ pm_runtime_put_autosuspend(cs42l42->dev);
return IRQ_NONE;
}
@@ -1750,6 +1771,8 @@ irqreturn_t cs42l42_irq_thread(int irq, void *data)
}
mutex_unlock(&cs42l42->irq_lock);
+ pm_runtime_mark_last_busy(cs42l42->dev);
+ pm_runtime_put_autosuspend(cs42l42->dev);
return IRQ_HANDLED;
Again in SoundWire more you should not use a dedicated interrupt.
There's something missing in the explanations on why this thread is
required.
Do you have a situation where it will actually cause a problem or are
you just saying that in an ideal world where all the hardware was
perfect it wouldn't need one?
Bear in mind that cs42l42 is roughly 7 years old so its Soundwire
implementation may not be all that you'd expect from a device designed
today to SW1.2 with Soundwire as its primary interface.