Re: [PATCH 04/15] can: m_can: Use transmit event FIFO watermark level interrupt
From: Marc Kleine-Budde
Date: Fri Dec 02 2022 - 04:33:48 EST
On 01.12.2022 17:59:51, Markus Schneider-Pargmann wrote:
> On Thu, Dec 01, 2022 at 12:00:33PM +0100, Marc Kleine-Budde wrote:
> > On 01.12.2022 11:12:20, Markus Schneider-Pargmann wrote:
> > > > > For the upcoming receive side patch I already added a hrtimer. I may try
> > > > > to use the same timer for both directions as it is going to do the exact
> > > > > same thing in both cases (call the interrupt routine). Of course that
> > > > > depends on the details of the coalescing support. Any objections on
> > > > > that?
> > > >
> > > > For the mcp251xfd I implemented the RX and TX coalescing independent of
> > > > each other and made it configurable via ethtool's IRQ coalescing
> > > > options.
> > > >
> > > > The hardware doesn't support any timeouts and only FIFO not empty, FIFO
> > > > half full and FIFO full IRQs and the on chip RAM for mailboxes is rather
> > > > limited. I think the mcan core has the same limitations.
> > >
> > > Yes and no, the mcan core provides watermark levels so it has more
> > > options, but there is no hardware timer as well (at least I didn't see
> > > anything usable).
> >
> > Are there any limitations to the water mark level?
>
> Anything specific? I can't really see any limitation. You can set the
> watermark between 1 and 32. I guess we could also always use it instead
> of the new-element interrupt, but I haven't tried that yet. That may
> simplify the code.
Makes sense.
> > > > The configuration for the mcp251xfd looks like this:
> > > >
> > > > - First decide for classical CAN or CAN-FD mode
> > > > - configure RX and TX ring size
> > > > 9263c2e92be9 ("can: mcp251xfd: ring: add support for runtime configurable RX/TX ring parameters")
> > > > For TX only a single FIFO is used.
> > > > For RX up to 3 FIFOs (up to a depth of 32 each).
> > > > FIFO depth is limited to power of 2.
> > > > On the mcan cores this is currently done with a DT property.
> > > > Runtime configurable ring size is optional but gives more flexibility
> > > > for our use-cases due to limited RAM size.
> > > > - configure RX and TX coalescing via ethtools
> > > > Set a timeout and the max CAN frames to coalesce.
> > > > The max frames are limited to half or full FIFO.
> > >
> > > mcan can offer more options for the max frames limit fortunately.
> > >
> > > >
> > > > How does coalescing work?
> > > >
> > > > If coalescing is activated during reading of the RX'ed frames the FIFO
> > > > not empty IRQ is disabled (the half or full IRQ stays enabled). After
> > > > handling the RX'ed frames a hrtimer is started. In the hrtimer's
> > > > functions the FIFO not empty IRQ is enabled again.
> > >
> > > My rx path patches are working similarly though not 100% the same. I
> > > will adopt everything and add it to the next version of this series.
> > >
> > > >
> > > > I decided not to call the IRQ handler from the hrtimer to avoid
> > > > concurrency, but enable the FIFO not empty IRQ.
> > >
> > > mcan uses a threaded irq and I found this nice helper function I am
> > > currently using for the receive path.
> > > irq_wake_thread()
> > >
> > > It is not widely used so I hope this is fine. But this hopefully avoids
> > > the concurrency issue. Also I don't need to artificially create an IRQ
> > > as you do.
> >
> > I think it's Ok to use the function. Which IRQs are enabled after you
> > leave the RX handler? The mcp251xfd driver enables only a high watermark
> > IRQ and sets up the hrtimer. Then we have 3 scenarios:
> > - high watermark IRQ triggers -> IRQ is handled,
> > - FIFO level between 0 and high water mark -> no IRQ triggered, but
> > hrtimer will run, irq_wake_thread() is called, IRQ is handled
> > - FIFO level 0 -> no IRQ triggered, hrtimer will run. What do you do in
> > the IRQ handler? Check if FIFO is empty and enable the FIFO not empty
> > IRQ?
>
> I am currently doing the normal IRQ handler run. It checks the
> "Interrupt Register" at the beginning. This register does not show the
> interrupts that fired, it shows the status. So even though the watermark
> interrupt didn't trigger when called by a timer, RF0N 'new message'
> status bit is still set if there is something new in the FIFO.
That covers scenario 2 from above.
> Of course it is the same for the transmit status bits.
ACK - The TX complete event handling is a 95% copy/paste of the RX
handling.
> So there is no need to read the FIFO fill levels directly, just the
> general status register.
What do you do if the hrtimer fires and there's no CAN frame waiting in
the FIFO?
Marc
--
Pengutronix e.K. | Marc Kleine-Budde |
Embedded Linux | https://www.pengutronix.de |
Vertretung West/Dortmund | Phone: +49-231-2826-924 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Attachment:
signature.asc
Description: PGP signature