[PATCH 03/18] arm64: dts: qcom: ipq6018: Sort nodes properly
From: Konrad Dybcio
Date: Sat Dec 31 2022 - 07:59:38 EST
Order nodes by unit address if one exists and alphabetically otherwise.
Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 489 ++++++++++++--------------
1 file changed, 223 insertions(+), 266 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index 4b74eee35971..2026000f3dc7 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -87,6 +87,12 @@ L2_0: l2-cache {
};
};
+ firmware {
+ scm {
+ compatible = "qcom,scm-ipq6018", "qcom,scm";
+ };
+ };
+
cpu_opp_table: opp-table-cpu {
compatible = "operating-points-v2";
opp-shared;
@@ -123,12 +129,6 @@ opp-1800000000 {
};
};
- firmware {
- scm {
- compatible = "qcom,scm-ipq6018", "qcom,scm";
- };
- };
-
pmuv8: pmu {
compatible = "arm,cortex-a53-pmu";
interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
@@ -166,6 +166,28 @@ q6_region: memory@4ab00000 {
};
};
+ rpm-glink {
+ compatible = "qcom,glink-rpm";
+ interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+ mboxes = <&apcs_glb 0>;
+
+ rpm_requests: glink-channel {
+ compatible = "qcom,rpm-ipq6018";
+ qcom,glink-channels = "rpm_requests";
+
+ regulators {
+ compatible = "qcom,rpm-mp5496-regulators";
+
+ ipq6018_s2: s2 {
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1062500>;
+ regulator-always-on;
+ };
+ };
+ };
+ };
+
smem {
compatible = "qcom,smem";
memory-region = <&smem_region>;
@@ -179,6 +201,102 @@ soc: soc {
dma-ranges;
compatible = "simple-bus";
+ qusb_phy_1: qusb@59000 {
+ compatible = "qcom,ipq6018-qusb2-phy";
+ reg = <0x0 0x00059000 0x0 0x180>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>,
+ <&xo>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2_1_PHY_BCR>;
+ status = "disabled";
+ };
+
+ ssphy_0: ssphy@78000 {
+ compatible = "qcom,ipq6018-qmp-usb3-phy";
+ reg = <0x0 0x00078000 0x0 0x1c4>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&gcc GCC_USB0_AUX_CLK>,
+ <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>;
+ clock-names = "aux", "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_USB0_PHY_BCR>,
+ <&gcc GCC_USB3PHY_0_PHY_BCR>;
+ reset-names = "phy","common";
+ status = "disabled";
+
+ usb0_ssphy: phy@78200 {
+ reg = <0x0 0x00078200 0x0 0x130>, /* Tx */
+ <0x0 0x00078400 0x0 0x200>, /* Rx */
+ <0x0 0x00078800 0x0 0x1f8>, /* PCS */
+ <0x0 0x00078600 0x0 0x044>; /* PCS misc */
+ #phy-cells = <0>;
+ #clock-cells = <0>;
+ clocks = <&gcc GCC_USB0_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_usb0_pipe_clk_src";
+ };
+ };
+
+ qusb_phy_0: qusb@79000 {
+ compatible = "qcom,ipq6018-qusb2-phy";
+ reg = <0x0 0x00079000 0x0 0x180>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
+ <&xo>;
+ clock-names = "cfg_ahb", "ref";
+
+ resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
+ status = "disabled";
+ };
+
+ pcie_phy: phy@84000 {
+ compatible = "qcom,ipq6018-qmp-pcie-phy";
+ reg = <0x0 0x00084000 0x0 0x1bc>; /* Serdes PLL */
+ status = "disabled";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+ <&gcc GCC_PCIE0_AHB_CLK>;
+ clock-names = "aux", "cfg_ahb";
+
+ resets = <&gcc GCC_PCIE0_PHY_BCR>,
+ <&gcc GCC_PCIE0PHY_PHY_BCR>;
+ reset-names = "phy",
+ "common";
+
+ pcie_phy0: phy@84200 {
+ reg = <0x0 0x00084200 0x0 0x16c>, /* Serdes Tx */
+ <0x0 0x00084400 0x0 0x200>, /* Serdes Rx */
+ <0x0 0x00084800 0x0 0x1f0>, /* PCS: Lane0, COM, PCIE */
+ <0x0 0x00084c00 0x0 0xf4>; /* pcs_misc */
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
+ clock-names = "pipe0";
+ clock-output-names = "gcc_pcie0_pipe_clk_src";
+ #clock-cells = <0>;
+ };
+ };
+
+ mdio: mdio@90000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "qcom,ipq6018-mdio", "qcom,ipq4019-mdio";
+ reg = <0x0 0x00090000 0x0 0x64>;
+ clocks = <&gcc GCC_MDIO_AHB_CLK>;
+ clock-names = "gcc_mdio_ahb_clk";
+ status = "disabled";
+ };
+
prng: qrng@e1000 {
compatible = "qcom,prng-ee";
reg = <0x0 0x000e3000 0x0 0x1000>;
@@ -257,6 +375,41 @@ tcsr: syscon@1937000 {
reg = <0x0 0x01937000 0x0 0x21000>;
};
+ usb2: usb@70f8800 {
+ compatible = "qcom,ipq6018-dwc3", "qcom,dwc3";
+ reg = <0x0 0x070F8800 0x0 0x400>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ clocks = <&gcc GCC_USB1_MASTER_CLK>,
+ <&gcc GCC_USB1_SLEEP_CLK>,
+ <&gcc GCC_USB1_MOCK_UTMI_CLK>;
+ clock-names = "core",
+ "sleep",
+ "mock_utmi";
+
+ assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>,
+ <&gcc GCC_USB1_MOCK_UTMI_CLK>;
+ assigned-clock-rates = <133330000>,
+ <24000000>;
+ resets = <&gcc GCC_USB1_BCR>;
+ status = "disabled";
+
+ dwc_1: usb@7000000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0x07000000 0x0 0xcd00>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&qusb_phy_1>;
+ phy-names = "usb2-phy";
+ tx-fifo-resize;
+ snps,is-utmi-l1-suspend;
+ snps,hird-threshold = /bits/ 8 <0x0>;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ dr_mode = "host";
+ };
+ };
+
blsp_dma: dma-controller@7884000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x0 0x07884000 0x0 0x2b000>;
@@ -374,13 +527,13 @@ usb3: usb@8af8800 {
ranges;
clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
- <&gcc GCC_USB0_MASTER_CLK>,
- <&gcc GCC_USB0_SLEEP_CLK>,
- <&gcc GCC_USB0_MOCK_UTMI_CLK>;
+ <&gcc GCC_USB0_MASTER_CLK>,
+ <&gcc GCC_USB0_SLEEP_CLK>,
+ <&gcc GCC_USB0_MOCK_UTMI_CLK>;
clock-names = "cfg_noc",
- "core",
- "sleep",
- "mock_utmi";
+ "core",
+ "sleep",
+ "mock_utmi";
assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
<&gcc GCC_USB0_MASTER_CLK>,
@@ -429,107 +582,6 @@ v2m@0 {
};
};
- pcie_phy: phy@84000 {
- compatible = "qcom,ipq6018-qmp-pcie-phy";
- reg = <0x0 0x00084000 0x0 0x1bc>; /* Serdes PLL */
- status = "disabled";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- clocks = <&gcc GCC_PCIE0_AUX_CLK>,
- <&gcc GCC_PCIE0_AHB_CLK>;
- clock-names = "aux", "cfg_ahb";
-
- resets = <&gcc GCC_PCIE0_PHY_BCR>,
- <&gcc GCC_PCIE0PHY_PHY_BCR>;
- reset-names = "phy",
- "common";
-
- pcie_phy0: phy@84200 {
- reg = <0x0 0x00084200 0x0 0x16c>, /* Serdes Tx */
- <0x0 0x00084400 0x0 0x200>, /* Serdes Rx */
- <0x0 0x00084800 0x0 0x1f0>, /* PCS: Lane0, COM, PCIE */
- <0x0 0x00084c00 0x0 0xf4>; /* pcs_misc */
- #phy-cells = <0>;
-
- clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
- clock-names = "pipe0";
- clock-output-names = "gcc_pcie0_pipe_clk_src";
- #clock-cells = <0>;
- };
- };
-
- pcie0: pci@20000000 {
- compatible = "qcom,pcie-ipq6018";
- reg = <0x0 0x20000000 0x0 0xf1d>,
- <0x0 0x20000f20 0x0 0xa8>,
- <0x0 0x20001000 0x0 0x1000>,
- <0x0 0x80000 0x0 0x4000>,
- <0x0 0x20100000 0x0 0x1000>;
- reg-names = "dbi", "elbi", "atu", "parf", "config";
-
- device_type = "pci";
- linux,pci-domain = <0>;
- bus-range = <0x00 0xff>;
- num-lanes = <1>;
- max-link-speed = <3>;
- #address-cells = <3>;
- #size-cells = <2>;
-
- phys = <&pcie_phy0>;
- phy-names = "pciephy";
-
- ranges = <0x81000000 0 0x20200000 0 0x20200000
- 0 0x10000>, /* downstream I/O */
- <0x82000000 0 0x20220000 0 0x20220000
- 0 0xfde0000>; /* non-prefetchable memory */
-
- interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "msi";
-
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0x7>;
- interrupt-map = <0 0 0 1 &intc 0 75
- IRQ_TYPE_LEVEL_HIGH>, /* int_a */
- <0 0 0 2 &intc 0 78
- IRQ_TYPE_LEVEL_HIGH>, /* int_b */
- <0 0 0 3 &intc 0 79
- IRQ_TYPE_LEVEL_HIGH>, /* int_c */
- <0 0 0 4 &intc 0 83
- IRQ_TYPE_LEVEL_HIGH>; /* int_d */
-
- clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
- <&gcc GCC_PCIE0_AXI_M_CLK>,
- <&gcc GCC_PCIE0_AXI_S_CLK>,
- <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
- <&gcc PCIE0_RCHNG_CLK>;
- clock-names = "iface",
- "axi_m",
- "axi_s",
- "axi_bridge",
- "rchng";
-
- resets = <&gcc GCC_PCIE0_PIPE_ARES>,
- <&gcc GCC_PCIE0_SLEEP_ARES>,
- <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
- <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
- <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
- <&gcc GCC_PCIE0_AHB_ARES>,
- <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
- <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
- reset-names = "pipe",
- "sleep",
- "sticky",
- "axi_m",
- "axi_s",
- "ahb",
- "axi_m_sticky",
- "axi_s_sticky";
-
- status = "disabled";
- };
-
watchdog@b017000 {
compatible = "qcom,kpss-wdt";
interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
@@ -662,147 +714,74 @@ qrtr_requests {
};
};
- mdio: mdio@90000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "qcom,ipq6018-mdio", "qcom,ipq4019-mdio";
- reg = <0x0 0x00090000 0x0 0x64>;
- clocks = <&gcc GCC_MDIO_AHB_CLK>;
- clock-names = "gcc_mdio_ahb_clk";
- status = "disabled";
- };
-
- qusb_phy_1: qusb@59000 {
- compatible = "qcom,ipq6018-qusb2-phy";
- reg = <0x0 0x00059000 0x0 0x180>;
- #phy-cells = <0>;
-
- clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>,
- <&xo>;
- clock-names = "cfg_ahb", "ref";
-
- resets = <&gcc GCC_QUSB2_1_PHY_BCR>;
- status = "disabled";
- };
-
- usb2: usb@70f8800 {
- compatible = "qcom,ipq6018-dwc3", "qcom,dwc3";
- reg = <0x0 0x070F8800 0x0 0x400>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
- clocks = <&gcc GCC_USB1_MASTER_CLK>,
- <&gcc GCC_USB1_SLEEP_CLK>,
- <&gcc GCC_USB1_MOCK_UTMI_CLK>;
- clock-names = "core",
- "sleep",
- "mock_utmi";
-
- assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>,
- <&gcc GCC_USB1_MOCK_UTMI_CLK>;
- assigned-clock-rates = <133330000>,
- <24000000>;
- resets = <&gcc GCC_USB1_BCR>;
- status = "disabled";
-
- dwc_1: usb@7000000 {
- compatible = "snps,dwc3";
- reg = <0x0 0x07000000 0x0 0xcd00>;
- interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&qusb_phy_1>;
- phy-names = "usb2-phy";
- tx-fifo-resize;
- snps,is-utmi-l1-suspend;
- snps,hird-threshold = /bits/ 8 <0x0>;
- snps,dis_u2_susphy_quirk;
- snps,dis_u3_susphy_quirk;
- dr_mode = "host";
- };
- };
+ pcie0: pci@20000000 {
+ compatible = "qcom,pcie-ipq6018";
+ reg = <0x0 0x20000000 0x0 0xf1d>,
+ <0x0 0x20000f20 0x0 0xa8>,
+ <0x0 0x20001000 0x0 0x1000>,
+ <0x0 0x80000 0x0 0x4000>,
+ <0x0 0x20100000 0x0 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
- ssphy_0: ssphy@78000 {
- compatible = "qcom,ipq6018-qmp-usb3-phy";
- reg = <0x0 0x00078000 0x0 0x1c4>;
- #address-cells = <2>;
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ max-link-speed = <3>;
+ #address-cells = <3>;
#size-cells = <2>;
- ranges;
-
- clocks = <&gcc GCC_USB0_AUX_CLK>,
- <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>;
- clock-names = "aux", "cfg_ahb", "ref";
- resets = <&gcc GCC_USB0_PHY_BCR>,
- <&gcc GCC_USB3PHY_0_PHY_BCR>;
- reset-names = "phy","common";
- status = "disabled";
-
- usb0_ssphy: phy@78200 {
- reg = <0x0 0x00078200 0x0 0x130>, /* Tx */
- <0x0 0x00078400 0x0 0x200>, /* Rx */
- <0x0 0x00078800 0x0 0x1f8>, /* PCS */
- <0x0 0x00078600 0x0 0x044>; /* PCS misc */
- #phy-cells = <0>;
- #clock-cells = <0>;
- clocks = <&gcc GCC_USB0_PIPE_CLK>;
- clock-names = "pipe0";
- clock-output-names = "gcc_usb0_pipe_clk_src";
- };
- };
-
- qusb_phy_0: qusb@79000 {
- compatible = "qcom,ipq6018-qusb2-phy";
- reg = <0x0 0x00079000 0x0 0x180>;
- #phy-cells = <0>;
+ phys = <&pcie_phy0>;
+ phy-names = "pciephy";
- clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
- <&xo>;
- clock-names = "cfg_ahb", "ref";
+ ranges = <0x81000000 0 0x20200000 0 0x20200000
+ 0 0x10000>, /* downstream I/O */
+ <0x82000000 0 0x20220000 0 0x20220000
+ 0 0xfde0000>; /* non-prefetchable memory */
- resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
- status = "disabled";
- };
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
- usb3: usb@8af8800 {
- compatible = "qcom,ipq6018-dwc3", "qcom,dwc3";
- reg = <0x0 0x8af8800 0x0 0x400>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 75
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 78
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 79
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 83
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
- clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
- <&gcc GCC_USB0_MASTER_CLK>,
- <&gcc GCC_USB0_SLEEP_CLK>,
- <&gcc GCC_USB0_MOCK_UTMI_CLK>;
- clock-names = "cfg_noc",
- "core",
- "sleep",
- "mock_utmi";
+ clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
+ <&gcc GCC_PCIE0_AXI_M_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
+ <&gcc PCIE0_RCHNG_CLK>;
+ clock-names = "iface",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
- assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
- <&gcc GCC_USB0_MASTER_CLK>,
- <&gcc GCC_USB0_MOCK_UTMI_CLK>;
- assigned-clock-rates = <133330000>,
- <133330000>,
- <20000000>;
+ resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+ <&gcc GCC_PCIE0_SLEEP_ARES>,
+ <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
+ <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
+ <&gcc GCC_PCIE0_AHB_ARES>,
+ <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
+ reset-names = "pipe",
+ "sleep",
+ "sticky",
+ "axi_m",
+ "axi_s",
+ "ahb",
+ "axi_m_sticky",
+ "axi_s_sticky";
- resets = <&gcc GCC_USB0_BCR>;
status = "disabled";
-
- dwc_0: usb@8a00000 {
- compatible = "snps,dwc3";
- reg = <0x0 0x8a00000 0x0 0xcd00>;
- interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&qusb_phy_0>, <&usb0_ssphy>;
- phy-names = "usb2-phy", "usb3-phy";
- clocks = <&xo>;
- clock-names = "ref";
- tx-fifo-resize;
- snps,is-utmi-l1-suspend;
- snps,hird-threshold = /bits/ 8 <0x0>;
- snps,dis_u2_susphy_quirk;
- snps,dis_u3_susphy_quirk;
- dr_mode = "host";
- };
};
};
@@ -837,26 +816,4 @@ wcss_smp2p_in: slave-kernel {
#interrupt-cells = <2>;
};
};
-
- rpm-glink {
- compatible = "qcom,glink-rpm";
- interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
- qcom,rpm-msg-ram = <&rpm_msg_ram>;
- mboxes = <&apcs_glb 0>;
-
- rpm_requests: glink-channel {
- compatible = "qcom,rpm-ipq6018";
- qcom,glink-channels = "rpm_requests";
-
- regulators {
- compatible = "qcom,rpm-mp5496-regulators";
-
- ipq6018_s2: s2 {
- regulator-min-microvolt = <725000>;
- regulator-max-microvolt = <1062500>;
- regulator-always-on;
- };
- };
- };
- };
};
--
2.39.0