Re: [PATCH v2 2/3] livepatch,sched: Add livepatch task switching to cond_resched()

[Petr Mladek]

On Fri 2023-02-17 14:22:55, Josh Poimboeuf wrote:
> There have been reports [1][2] of live patches failing to complete
> within a reasonable amount of time due to CPU-bound kthreads.
> 
> Fix it by patching tasks in cond_resched().
> 
> There are four different flavors of cond_resched(), depending on the
> kernel configuration.  Hook into all of them.
> 
> A more elegant solution might be to use a preempt notifier.  However,
> non-ORC unwinders can't unwind a preempted task reliably.
> 
> [1] https://lore.kernel.org/lkml/20220507174628.2086373-1-song@xxxxxxxxxx/
> [2] https://lkml.kernel.org/lkml/20230120-vhost-klp-switching-v1-0-7c2b65519c43@xxxxxxxxxx
> 
> --- a/kernel/livepatch/transition.c
> +++ b/kernel/livepatch/transition.c
> @@ -588,14 +641,10 @@ void klp_reverse_transition(void)
>  		 klp_target_state == KLP_PATCHED ? "patching to unpatching" :
>  						   "unpatching to patching");
>  
> -	klp_transition_patch->enabled = !klp_transition_patch->enabled;
> -
> -	klp_target_state = !klp_target_state;
> -
>  	/*
>  	 * Clear all TIF_PATCH_PENDING flags to prevent races caused by
> -	 * klp_update_patch_state() running in parallel with
> -	 * klp_start_transition().
> +	 * klp_update_patch_state() or __klp_sched_try_switch() running in
> +	 * parallel with the reverse transition.
>  	 */
>  	read_lock(&tasklist_lock);
>  	for_each_process_thread(g, task)
> @@ -605,9 +654,16 @@ void klp_reverse_transition(void)
>  	for_each_possible_cpu(cpu)
>  		clear_tsk_thread_flag(idle_task(cpu), TIF_PATCH_PENDING);
>  
> -	/* Let any remaining calls to klp_update_patch_state() complete */
> +	/*
> +	 * Make sure all existing invocations of klp_update_patch_state() and
> +	 * __klp_sched_try_switch() see the cleared TIF_PATCH_PENDING before
> +	 * starting the reverse transition.
> +	 */
>  	klp_synchronize_transition();
>  
> +	/* All patching has stopped, now start the reverse transition. */
> +	klp_transition_patch->enabled = !klp_transition_patch->enabled;
> +	klp_target_state = !klp_target_state;

I have double checked the synchronization and we need here:

	/*
	 * Make sure klp_update_patch_state() and __klp_sched_try_switch()
	 * see the updated klp_target_state before TIF_PATCH_PENDING
	 * is set again in klp_start_transition().
	 */
	smp_wmb();

The same is achieved by smp_wmb() in klp_init_transition().

Note that the extra barrier was missing here because klp_target_state
was set before klp_synchronize_transition(). It was fine because
klp_update_patch_state() was called on locations where a transition
in any direction was always safe.

Just for record. We need to modify @klp_target_state after
klp_synchronize_transition() now. The value is used by
__klp_sched_try_switch() to decide when the transition
is safe. It defines what functions must not be on the stack.

I am sorry that I missed this when reviewing v1. I think that I needed
to see the new code with a fresh head.

>  	klp_start_transition();
>  }

I do not see any other problem. With the above barrier added,
feel free to use:

Reviewed-by: Petr Mladek <pmladek@xxxxxxxx>

It is for the livepatching part. I checked also the scheduler
code and it looked fine but I would not put my hand in the fire
for it.

Best Regards,
Petr