Re: [PATCH 3/5] arm64: dts: mediatek: cherry: Configure eDP and internal display

[Chen-Yu Tsai]

On Thu, Apr 20, 2023 at 5:45 PM AngeloGioacchino Del Regno
<angelogioacchino.delregno@xxxxxxxxxxxxx> wrote:
>
> Add the required nodes to enable the DisplayPort interface, connected
> to the Embedded DisplayPort port, where we have an internal display.
>
> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx>
> ---
>  .../boot/dts/mediatek/mt8195-cherry.dtsi      | 32 +++++++++++++++++++
>  1 file changed, 32 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi b/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
> index 918380697a9a..46f1c8091498 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
> @@ -49,6 +49,18 @@ memory@40000000 {
>                 reg = <0 0x40000000 0 0x80000000>;
>         };
>
> +       pp3300_disp_x: regulator-pp3300-disp-x {
> +               compatible = "regulator-fixed";
> +               regulator-name = "pp3300_disp_x";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;

>From the schematics:
                  vin-supply = <&pp3300_z2>;

Also, this is an RT9742. The datasheet says the typical enable time is
2.1ms. For a bit of margin, I'd say we could model it as 2.5ms? So:

                  regulator-enable-ramp-delay = <2500>;

ChenYu

> +               enable-active-high;
> +               gpio = <&pio 55 GPIO_ACTIVE_HIGH>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&panel_fixed_pins>;
> +               regulator-always-on;
> +       };
> +
>         /* system wide LDO 3.3V power rail */
>         pp3300_z5: regulator-pp3300-ldo-z5 {
>                 compatible = "regulator-fixed";
> @@ -290,6 +302,20 @@ port@1 {
>                         reg = <1>;
>                         edp_out: endpoint {
>                                 data-lanes = <0 1 2 3>;
> +                               remote-endpoint = <&panel_in>;
> +                       };
> +               };
> +       };
> +
> +       aux-bus {
> +               panel {
> +                       compatible = "edp-panel";
> +                       power-supply = <&pp3300_disp_x>;
> +                       backlight = <&backlight_lcd0>;
> +                       port {
> +                               panel_in: endpoint {
> +                                       remote-endpoint = <&edp_out>;
> +                               };
>                         };
>                 };
>         };
> @@ -929,6 +955,12 @@ pins-cs {
>                 };
>         };
>
> +       panel_fixed_pins: panel-pwr-default-pins {
> +               pins-vreg-en {
> +                       pinmux = <PINMUX_GPIO55__FUNC_GPIO55>;
> +               };
> +       };
> +
>         pio_default: pio-default-pins {
>                 pins-wifi-enable {
>                         pinmux = <PINMUX_GPIO58__FUNC_GPIO58>;
> --
> 2.40.0
>
>