RE: [PATCH v1 2/2] doc: dt: bindings: usb: realtek,dwc3: Add Realtek DHC RTD SoC DWC3 USB

[Stanley Chang[昌育德]]

Hi Rob,

> > +properties:
> > +  compatible:
> > +    items:
> > +      - enum:
> > +          - realtek,rtd1295-dwc3
> > +          - realtek,rtd1315e-dwc3
> > +          - realtek,rtd1319-dwc3
> > +          - realtek,rtd1319d-dwc3
> > +          - realtek,rtd1395-dwc3
> > +          - realtek,rtd1619-dwc3
> > +          - realtek,rtd1619b-dwc3
> > +      - const: realtek,rtd-dwc3
> > +
> > +  reg:
> > +    maxItems: 1
> 
> Some details on what these registers are would be useful. Or describing what's
> in the 'glue' device?

Ok, I will add the description.
 

> > +  realtek,unlink-usb3-port:
> > +    description: Disable link between USB 3.0 PHY and USB mac.
> > +      Only for RTD1619 SoC, if the board design support maximum 2.0
> speed.
> > +    type: boolean
> 
> We have a property for this: maximum-speed
> 
> That belongs in the USB controller node though.

I can try to use this property.
But I have a question.
This property belongs to dwc3.
When the dwc3-rtk setting disables USB 3.0 phy, dwc3 is not probed.
So I can't use api usb_get_maximum_speed(dev) to get maximum_speed.

I can add this property "maximum-speed" to the dwc3-rtk node, which is the same as the dwc3 core node.
Is this configuration appropriate? 
For example 
    usb@98013e00 {
        compatible = "realtek,rtd1319d-dwc3", "realtek,rtd-dwc3";
        reg = <0x98013e00 0x200>;
        #address-cells = <1>;
        #size-cells = <1>;
        ranges;
        maximum-speed = "high-speed";

        usb@98050000 {
            compatible = "snps,dwc3";
            reg = <0x98050000 0x9000>;
            interrupts = <0 94 4>;
            phys = <&usb2phy &usb3phy>;
            phy-names = "usb2-phy", "usb3-phy";
            dr_mode = "otg";
            usb-role-switch;
            role-switch-default-mode = "host";
            snps,dis_u2_susphy_quirk;
            snps,parkmode-disable-ss-quirk;
            snps,parkmode-disable-hs-quirk;
            maximum-speed = "high-speed";
        };
    };

> > +
> > +  realtek,disable-usb3-phy:
> > +    description: Close USB 3.0 PHY if the board design not support USB 3.0.
> > +    type: boolean
> 
> Can't this be determined by not having a USB3 phy listed?

I will try to use maximum-speed.

> > +examples:
> > +  - |
> > +    usb@98013e00 {
> > +        compatible = "realtek,rtd1319d-dwc3", "realtek,rtd-dwc3";
> > +        reg = <0x98013e00 0x200>;
> > +        #address-cells = <1>;
> > +        #size-cells = <1>;
> > +        ranges;
> > +        status = "okay";
> 
> Drop status from examples.

Ok.

Thanks,
Stanley