Re: [-next v1] riscv: dts: starfive: visionfive 2: Enable usb0 and fix tdm pins sort order

[Hal Feng]

On Mon, 28 Aug 2023 13:05:06 +0100, Conor Dooley wrote:
> On Mon, Aug 28, 2023 at 01:54:53PM +0200, Krzysztof Kozlowski wrote:
>> On 28/08/2023 13:52, Hal Feng wrote:
>> > usb0 was disabled by mistake when merging, so enable it.
>> > tdm_pins node should be sorted alphabetically.
>> > 
>> > Fixes: e7c304c0346d ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
>> > Signed-off-by: Hal Feng <hal.feng@xxxxxxxxxxxxxxxx>
>> > ---
>> >  .../jh7110-starfive-visionfive-2.dtsi         | 49 ++++++++++---------
>> >  1 file changed, 25 insertions(+), 24 deletions(-)
>> > 
>> > diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
>> > index d79f94432b27..382dfb5e64e4 100644
>> > --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
>> > +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
>> > @@ -440,30 +440,6 @@ GPOEN_ENABLE,
>> >  		};
>> >  	};
>> >  
>> > -	uart0_pins: uart0-0 {
>> > -		tx-pins {
>> > -			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
>> > -					     GPOEN_ENABLE,
>> > -					     GPI_NONE)>;
>> > -			bias-disable;
>> > -			drive-strength = <12>;
>> > -			input-disable;
>> > -			input-schmitt-disable;
>> > -			slew-rate = <0>;
>> > -		};
>> > -
>> > -		rx-pins {
>> > -			pinmux = <GPIOMUX(6, GPOUT_LOW,
>> > -					     GPOEN_DISABLE,
>> > -					     GPI_SYS_UART0_RX)>;
>> > -			bias-disable; /* external pull-up */
>> > -			drive-strength = <2>;
>> > -			input-enable;
>> > -			input-schmitt-enable;
>> > -			slew-rate = <0>;
>> > -		};
>> > -	};
>> > -
>> >  	tdm_pins: tdm-0 {
>> >  		tx-pins {
>> >  			pinmux = <GPIOMUX(44, GPOUT_SYS_TDM_TXD,
>> > @@ -497,6 +473,30 @@ GPOEN_DISABLE,
>> >  			input-enable;
>> >  		};
>> >  	};
>> > +
>> > +	uart0_pins: uart0-0 {
>> > +		tx-pins {
>> > +			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
>> > +					     GPOEN_ENABLE,
>> > +					     GPI_NONE)>;
>> > +			bias-disable;
>> > +			drive-strength = <12>;
>> > +			input-disable;
>> > +			input-schmitt-disable;
>> > +			slew-rate = <0>;
>> > +		};
>> > +
>> > +		rx-pins {
>> > +			pinmux = <GPIOMUX(6, GPOUT_LOW,
>> > +					     GPOEN_DISABLE,
>> > +					     GPI_SYS_UART0_RX)>;
>> > +			bias-disable; /* external pull-up */
>> > +			drive-strength = <2>;
>> > +			input-enable;
>> > +			input-schmitt-enable;
>> > +			slew-rate = <0>;
>> > +		};
>> 
>> 
>> What is fixed in this hunk? Order of nodes is just a style, not a bug
>> needing backports.
> 
> Please split this in two parts, with one for my screwed up conflict
> resolution & one for the node ordering.

OK, I will split this into two patches. Thanks.

Best regards,
Hal