Re: [PATCH 2/2] arm64: dts: qcom: add TP-Link Archer AX55 v1

[Gabor Juhos]

Hi Krzysztof,

> On 23/02/2024 09:17, Gabor Juhos wrote:

<snip>

>> ---
>> Note: running 'make CHECK_DTBS=y qcom/ipq5018-tplink-archer-ax55-v1.dtb'
>> shows the following:
>>
>>     DTC_CHK arch/arm64/boot/dts/qcom/ipq5018-tplink-archer-ax55-v1.dtb
>>   <...>/arch/arm64/boot/dts/qcom/ipq5018-tplink-archer-ax55-v1.dtb: usb@8af8800: interrupts: [[0, 62, 4]] is too short
>>   	from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
>>   <...>/arch/arm64/boot/dts/qcom/ipq5018-tplink-archer-ax55-v1.dtb: usb@8af8800: interrupt-names: ['hs_phy_irq'] is too short
>>   	from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
>>   <...>/arch/arm64/boot/dts/qcom/ipq5018-tplink-archer-ax55-v1.dtb: usb@8af8800: interrupts: [[0, 62, 4]] is too short
>>   	from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
>>   <...>/arch/arm64/boot/dts/qcom/ipq5018-tplink-archer-ax55-v1.dtb: usb@8af8800: interrupt-names:0: 'pwr_event' was expected
>>   	from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
>>   <...>/arch/arm64/boot/dts/qcom/ipq5018-tplink-archer-ax55-v1.dtb: usb@8af8800: interrupt-names: ['hs_phy_irq'] is too short
>>   	from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
>>
>> This is not caused by the new device tree per se but comes from
>> the usb@8af8800 node defined in ipq5018.dtsi. Running the check
>> on 'qcom/ipq5018-rdp432-c2.dtb' shows the same.
> 
> Thanks for noticing and describing. Appreciated!

FWIW, I have checked that in the meantime. The warning happens since commit
53c6d854be4e ("dt-bindings: usb: dwc3: Clean up hs_phy_irq in binding").
Reverting that eliminates the warning.

> 
>> ---
>>  arch/arm64/boot/dts/qcom/Makefile                  |   1 +
>>  .../dts/qcom/ipq5018-tplink-archer-ax55-v1.dts     | 133 +++++++++++++++++++++
>>  2 files changed, 134 insertions(+)
> 
> ...

<snip>

>> +
>> +&tlmm {
>> +	button_pins: button-pins-state {
>> +		pins = "gpio25", "gpio31";
>> +		bias-pull-up;
>> +		drive-strength = <8>;
>> +		function = "gpio";
> 
> Usually we keep 'function' as second property, after 'pins', but there
> is no need to send new version just for that.

Sorry, it is my fault. I should have noticed that pattern based on the other dts
files. Nevertheless, I can send a v2 or a follow-up patch to fix the ordering so
we can avoid having a bad example in the tree.

> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>

Thank you for the review!

Regards,
Gabor