Re: [PATCH v2 3/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS

[Sumit Garg]

On Thu, 14 Mar 2024 at 14:00, Krzysztof Kozlowski
<krzysztof.kozlowski@xxxxxxxxxx> wrote:
>
> >>> +
> >>> +             compatible = "gpio-leds";
> >>> +             #address-cells = <1>;
> >>> +             #size-cells = <0>;
> >>
> >> That's not a bus.
> >>
> >> It does not look like you tested the DTS against bindings. Please run
> >> `make dtbs_check W=1` (see
> >> Documentation/devicetree/bindings/writing-schema.rst or
> >> https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
> >> for instructions).
> >
> > I assumed earlier that W=1 is sufficient for DT schema checks but it
>
> W=1 as in make? No, it is not. It's flag changing the build process.
> dtbs_check is separate target.
>
> > looks like those are two different entities. However, I added these
> > address and size cells properties only to get rid of warnings reported
> > by W=1, see below:
> >
> > $ make qcom/apq8016-schneider-hmibsc.dtb W=1
> >   DTC     arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb
> > arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts:96.9-103.5:
> > Warning (unit_address_vs_reg): /leds/led@5: node has a unit name, but
> > no reg or ranges property
> > arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts:105.9-112.5:
> > Warning (unit_address_vs_reg): /leds/led@6: node has a unit name, but
> > no reg or ranges property
>
> Wait, so you saw the warnings and ignored them?

Sorry but you are ignoring what I am trying to say.

> These are legitimate
> warnings, although they don't give you full answer.
>
> > <snip>
> >
> > So it looks like W=1 is reporting false warnings and we should rather
>
> Warnings were true.
>

That's was my initial impression too and I fixed them via following diff:

diff --git a/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
b/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
index 8f9cacf8de89..a366d3aff3c5 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
+++ b/arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts
@@ -92,8 +92,11 @@ leds {
                pinctrl-0 = <&pm8916_mpps_leds>;

                compatible = "gpio-leds";
+               #address-cells = <1>;
+               #size-cells = <0>;

                led@5 {
+                       reg = <5>;
                        label = "apq8016-hmibsc:green:wlan";
                        function = LED_FUNCTION_WLAN;
                        color = <LED_COLOR_ID_YELLOW>;
@@ -103,6 +106,7 @@ led@5 {
                };

                led@6 {
+                       reg = <6>;
                        label = "apq8016-hmibsc:yellow:bt";
                        function = LED_FUNCTION_BLUETOOTH;
                        color = <LED_COLOR_ID_BLUE>;

But it then broke dtbs_check. Are you aware of any other saner way to
fix those warnings properly?

-Sumit