[PATCH 2/2] arm64: dts: qcom: x1e80100-pmics: Add the missing PMICs

From: Konrad Dybcio
Date: Wed May 29 2024 - 07:18:05 EST

Next message: Kirill A. Shutemov: "Re: [PATCHv11 05/19] x86/relocate_kernel: Use named labels for less confusion"
Previous message: Konrad Dybcio: "[PATCH 1/2] dt-bindings: mfd: qcom,spmi-pmic: Document PMC8380 and SMB2360"
In reply to: Konrad Dybcio: "Re: [PATCH 1/2] dt-bindings: mfd: qcom,spmi-pmic: Document PMC8380 and SMB2360"
Next in thread: Bjorn Andersson: "Re: (subset) [PATCH 0/2] X1E PMICs"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

During the initial bringup, all of the peripherals on non-SMB PMICs
were either not used, or were not necessary to accomplish certain
goals. This however, left a hole in the hardware description.

Add the missing ones.

Note that the PM8010 errors out on reads on the CRD (works fine on the
QCP) for reasons unknown, but that shall be ironed out in the future..

Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi | 480 +++++++++++++++++++++++++++
1 file changed, 480 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi b/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
index 04301f772fbd..a5662d39fdff 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
@@ -3,10 +3,477 @@
* Copyright (c) 2024, Linaro Limited
*/

+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>

/ {
+ thermal-zones {
+ pm8550-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550ve-2-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550ve_2_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmc8380-3-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pmc8380_3_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmc8380-4-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pmc8380_4_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmc8380-5-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pmc8380_5_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmc8380-6-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pmc8380_6_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550ve-8-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550ve_8_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550ve-9-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8550ve_9_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8010-thermal {
+ polling-delay-passive = <100>;
+
+ thermal-sensors = <&pm8010_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus0 {
+ /* PMK8380 */
+ pmk8550: pmic@0 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmk8550_pon: pon@1300 {
+ compatible = "qcom,pmk8350-pon";
+ reg = <0x1300>, <0x800>;
+ reg-names = "hlos", "pbs";
+
+ pon_pwrkey: pwrkey {
+ compatible = "qcom,pmk8350-pwrkey";
+ interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
+ linux,code = <KEY_POWER>;
+ };
+
+ pon_resin: resin {
+ compatible = "qcom,pmk8350-resin";
+ interrupts = <0x0 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
+ status = "disabled";
+ };
+ };
+
+ pmk8550_rtc: rtc@6100 {
+ compatible = "qcom,pmk8350-rtc";
+ reg = <0x6100>, <0x6200>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
+ /* Not yet sure what blocks access */
+ status = "reserved";
+ };
+
+ pmk8550_sdam_2: nvram@7100 {
+ compatible = "qcom,spmi-sdam";
+ reg = <0x7100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x7100 0x100>;
+
+ reboot_reason: reboot-reason@48 {
+ reg = <0x48 0x1>;
+ bits = <1 7>;
+ };
+ };
+
+ pmk8550_gpios: gpio@8800 {
+ compatible = "qcom,pmk8550-gpio", "qcom,spmi-gpio";
+ reg = <0xb800>;
+ gpio-controller;
+ gpio-ranges = <&pmk8550_gpios 0 0 6>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ /* PMC8380C */
+ pm8550: pmic@1 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550_gpios: gpio@8800 {
+ compatible = "qcom,pm8550-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550_gpios 0 0 12>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pm8550_flash: led-controller@ee00 {
+ compatible = "qcom,pm8550-flash-led", "qcom,spmi-flash-led";
+ reg = <0xee00>;
+ status = "disabled";
+ };
+
+ pm8550_pwm: pwm {
+ compatible = "qcom,pm8550-pwm", "qcom,pm8350c-pwm";
+ #pwm-cells = <2>;
+
+ status = "disabled";
+ };
+ };
+
+ /* PMC8380VE */
+ pm8550ve_2: pmic@2 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x2 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550ve_2_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550ve_2_gpios: gpio@8800 {
+ compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550ve_2_gpios 0 0 8>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ /* PMC8380 is actually not a PM8550 series rebrand */
+ pmc8380_3: pmic@3 {
+ compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+ reg = <0x3 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8380_3_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8380_3_gpios: gpio@8800 {
+ compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8380_3_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmc8380_4: pmic@4 {
+ compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8380_4_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8380_4_gpios: gpio@8800 {
+ compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8380_4_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmc8380_5: pmic@5 {
+ compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+ reg = <0x5 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8380_5_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x5 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8380_5_gpios: gpio@8800 {
+ compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8380_5_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmc8380_6: pmic@6 {
+ compatible = "qcom,pmc8380", "qcom,spmi-pmic";
+ reg = <0x6 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmc8380_6_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmc8380_6_gpios: gpio@8800 {
+ compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmc8380_6_gpios 0 0 10>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ /* PMC8380VE */
+ pm8550ve_8: pmic@8 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x8 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550ve_8_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x8 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550ve_8_gpios: gpio@8800 {
+ compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550ve_8_gpios 0 0 8>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ /* PMC8380VE */
+ pm8550ve_9: pmic@9 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x9 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550ve_9_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x9 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550ve_9_gpios: gpio@8800 {
+ compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550ve_9_gpios 0 0 8>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8010: pmic@c {
+ compatible = "qcom,pm8010", "qcom,spmi-pmic";
+ reg = <0xc SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8010_temp_alarm: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0xc 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+ };
};

&spmi_bus1 {
@@ -48,4 +515,17 @@ smb2360_2_eusb2_repeater: phy@fd00 {
#phy-cells = <0>;
};
};
+
+ smb2360_3: pmic@c {
+ compatible = "qcom,smb2360", "qcom,spmi-pmic";
+ reg = <0xc SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ smb2360_3_eusb2_repeater: phy@fd00 {
+ compatible = "qcom,smb2360-eusb2-repeater";
+ reg = <0xfd00>;
+ #phy-cells = <0>;
+ };
+ };
};

--
2.45.1

Next message: Kirill A. Shutemov: "Re: [PATCHv11 05/19] x86/relocate_kernel: Use named labels for less confusion"
Previous message: Konrad Dybcio: "[PATCH 1/2] dt-bindings: mfd: qcom,spmi-pmic: Document PMC8380 and SMB2360"
In reply to: Konrad Dybcio: "Re: [PATCH 1/2] dt-bindings: mfd: qcom,spmi-pmic: Document PMC8380 and SMB2360"
Next in thread: Bjorn Andersson: "Re: (subset) [PATCH 0/2] X1E PMICs"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]