Re: [PATCH 1/1] dt-bindings: mmc: Convert fsl-esdhc.txt to yaml

[Frank Li]

On Sat, Jun 01, 2024 at 05:25:46PM +0200, Krzysztof Kozlowski wrote:
> On 31/05/2024 21:37, Frank Li wrote:
> > Convert layerscape fsl-esdhc binding doc from txt to yaml format.
> > 
> > Addtional change during convert:
> > - deprecate "sdhci,wp-inverted", "sdhci,1-bit-only".
> > - Add "reg" and "interrupts" property.
> > - change example "sdhci@2e000" to "mmc@2e000".
> > - compatible string require fsl,<chip>-esdhc followed by fsl,esdhc to match
> > most existed dts file.
> > 
> 
> 
> > -};
> > diff --git a/Documentation/devicetree/bindings/mmc/fsl-ls-esdhc.yaml b/Documentation/devicetree/bindings/mmc/fsl-ls-esdhc.yaml
> > new file mode 100644
> > index 0000000000000..cafc09c4f1234
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/mmc/fsl-ls-esdhc.yaml
> 
> Filename: fsl,esdhc.yaml

There is fsl-imx-esdhc.yaml for freescale imx esdhc. If use "fsl,esdhc.yam",
it may confuse user, which will cover imx chips also, actually it is only
used for layerscape chips.

Frank

> 
> > @@ -0,0 +1,98 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> 
> ...
> 
> > +  clock-frequency:
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +    description: specifies eSDHC base clock frequency.
> > +
> > +  sdhci,wp-inverted:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    deprecated: true
> > +    description:
> > +      specifies that eSDHC controller reports
> > +      inverted write-protect state; New devices should use the generic
> > +      "wp-inverted" property.
> > +
> > +  sdhci,1-bit-only:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    deprecated: true
> > +    description:
> > +      specifies that a controller can only handle
> > +      1-bit data transfers. New devices should use the generic
> > +      "bus-width = <1>" property.
> > +
> > +  sdhci,auto-cmd12:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description:
> > +      specifies that a controller can only handle auto CMD12.
> > +
> > +  voltage-ranges:
> > +    $ref: /schemas/types.yaml#/definitions/uint32-matrix
> > +    items:
> > +      items:
> > +        - description: specifies minimum slot voltage (mV).
> > +        - description: specifies maximum slot voltage (mV).
> > +
> > +  little-endian:
> > +    $ref: /schemas/types.yaml#/definitions/flag
> > +    description:
> > +      If the host controller is little-endian mode, specify
> > +      this property. The default endian mode is big-endian.
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - interrupts
> 
> clock-frequency was required. Isn't it required now?
> 
> > +
> > +allOf:
> > +  - $ref: sdhci-common.yaml#
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > +  - |
> > +    mmc@2e000 {
> > +        compatible = "fsl,mpc8378-esdhc", "fsl,esdhc";
> > +        reg = <0x2e000 0x1000>;
> > +        interrupts = <42 0x8>;
> > +        interrupt-parent = <&ipic>;
> > +        /* Filled in by U-Boot */
> > +        clock-frequency = <0>;
> 
> Please provide complete (final) example.
> 
> > +        voltage-ranges = <3300 3300>;
> > +    };
> 
> Best regards,
> Krzysztof
>