Re: [PATCH] ARM: dts: microchip: sam9x60: Move i2c address/size to dtsi

From: claudiu beznea
Date: Fri Aug 09 2024 - 02:15:26 EST




On 28.05.2024 18:31, Alexander Dahl wrote:
> These properties are common for all i2c subnodes, and marked as
> 'required' in atmel/microchip i2c bindings. Allows to add i2c device
> nodes (like an rtc for example) in other .dts files including
> sam9x60.dtsi without requiring to repeat these properties for each i2c
> device again and again.
>
> Found on a custom board after adding this in .dts:
>
> &flx5 {
> atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
> status = "okay";
>
> i2c5: i2c@600 {
> pinctrl-0 = <&pinctrl_flx5_default>;
> status = "okay";
>
> pcf8523: rtc@68 {
> compatible = "nxp,pcf8523";
> reg = <0x68>;
> };
> };
> };
>
> … which created a warning like this:
>
> […]:236.4-17: Warning (reg_format):
> /ahb/apb/flexcom@f0004000/i2c@600/rtc@68:reg: property has invalid
> length (4 bytes) (#address-cells == 2, #size-cells == 1)
> […]: Warning (pci_device_reg): Failed prerequisite 'reg_format'
> […]: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
> […]: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
>
> […]/linux-6.6.25/arch/arm/boot/dts/microchip/sam9x60.dtsi:283.19-299.7:
> Warning (i2c_bus_bridge): /ahb/apb/flexcom@f0004000/i2c@600: incorrect
> #address-cells for I2C bus also defined at […]:228.16-238.4
>
> […]/linux-6.6.25/arch/arm/boot/dts/microchip/sam9x60.dtsi:283.19-299.7:
> Warning (i2c_bus_bridge): /ahb/apb/flexcom@f0004000/i2c@600: incorrect
> #size-cells for I2C bus also defined at […]:228.16-238.4
> […]: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
> […]: Warning (i2c_bus_reg): Failed prerequisite 'i2c_bus_bridge'
> […]: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
> […]:234.19-237.5: Warning (avoid_default_addr_size):
> /ahb/apb/flexcom@f0004000/i2c@600/rtc@68: Relying on default
> #address-cells value
> […]:234.19-237.5: Warning (avoid_default_addr_size):
> /ahb/apb/flexcom@f0004000/i2c@600/rtc@68: Relying on default #size-cells
> value
> […]: Warning (avoid_unnecessary_addr_size): Failed prerequisite
> 'avoid_default_addr_size'
> […]: Warning (unique_unit_address): Failed prerequisite
> 'avoid_default_addr_size'
>
> This probably should have been done with commit 84f23f3284d5 ("ARM: dts:
> at91: sam9x60: move flexcom definitions") already, where those
> address-cells and size-cells properties were left in the board .dts
> files instead of moving them to the dtsi.
>
> Signed-off-by: Alexander Dahl <ada@xxxxxxxxxxx>


Applied to at91-dt, thanks!

Please note that I've adjusted the commit message to reflect that the props
you've adjusted are not required anymore in the validation schema.

Thank you,
Claudiu Beznea