[PATCH v5 07/12] arm64: dts: ti: k3-j784s4-j742s2-evm-common: Remove parent nodes bootph-*
From: Manorit Chawdhry
Date: Wed Oct 23 2024 - 03:00:20 EST
Adding bootph properties on leaf nodes imply that they are applicable to
the parent nodes as well. Bootloaders can derive the parent nodes when
bootph is available in the leaf nodes.
Remove the bootph-* properties from parent nodes as they are redundant.
Signed-off-by: Manorit Chawdhry <m-chawdhry@xxxxxx>
---
arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi | 9 ---------
1 file changed, 9 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
index 98453171a179..b2e2b9f507a9 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
@@ -305,7 +305,6 @@ &wkup_gpio0 {
};
&main_pmx0 {
- bootph-all;
main_cpsw2g_default_pins: main-cpsw2g-default-pins {
pinctrl-single,pins = <
J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
@@ -432,7 +431,6 @@ J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
};
&wkup_pmx2 {
- bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -548,7 +546,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
};
&wkup_pmx0 {
- bootph-all;
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -568,7 +565,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
};
&wkup_pmx1 {
- bootph-all;
mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -740,18 +736,15 @@ &ufs_wrapper {
};
&fss {
- bootph-all;
status = "okay";
};
&ospi0 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <8>;
@@ -808,13 +801,11 @@ partition@3fc0000 {
};
&ospi1 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <1>;
--
2.46.0