Re: [PATCH v5 07/12] arm64: dts: ti: k3-j784s4-j742s2-evm-common: Remove parent nodes bootph-*

[Aniket Limaye]

On 23/10/24 12:27, Manorit Chawdhry wrote:
> Adding bootph properties on leaf nodes imply that they are applicable to
> the parent nodes as well. Bootloaders can derive the parent nodes when
> bootph is available in the leaf nodes.
>
> Remove the bootph-* properties from parent nodes as they are redundant.
>
> Signed-off-by: Manorit Chawdhry <m-chawdhry@xxxxxx>

Reviewed-by: Aniket Limaye <a-limaye@xxxxxx>

> ---
>   arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi | 9 ---------
>   1 file changed, 9 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
> index 98453171a179..b2e2b9f507a9 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
> @@ -305,7 +305,6 @@ &wkup_gpio0 {
>   };
>   
>   &main_pmx0 {
> -	bootph-all;
>   	main_cpsw2g_default_pins: main-cpsw2g-default-pins {
>   		pinctrl-single,pins = <
>   			J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
> @@ -432,7 +431,6 @@ J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
>   };
>   
>   &wkup_pmx2 {
> -	bootph-all;
>   	wkup_uart0_pins_default: wkup-uart0-default-pins {
>   		bootph-all;
>   		pinctrl-single,pins = <
> @@ -548,7 +546,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
>   };
>   
>   &wkup_pmx0 {
> -	bootph-all;
>   	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
>   		bootph-all;
>   		pinctrl-single,pins = <
> @@ -568,7 +565,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
>   };
>   
>   &wkup_pmx1 {
> -	bootph-all;
>   	mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
>   		bootph-all;
>   		pinctrl-single,pins = <
> @@ -740,18 +736,15 @@ &ufs_wrapper {
>   };
>   
>   &fss {
> -	bootph-all;
>   	status = "okay";
>   };
>   
>   &ospi0 {
> -	bootph-all;
>   	status = "okay";
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
>   
>   	flash@0 {
> -		bootph-all;
>   		compatible = "jedec,spi-nor";
>   		reg = <0x0>;
>   		spi-tx-bus-width = <8>;
> @@ -808,13 +801,11 @@ partition@3fc0000 {
>   };
>   
>   &ospi1 {
> -	bootph-all;
>   	status = "okay";
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
>   
>   	flash@0 {
> -		bootph-all;
>   		compatible = "jedec,spi-nor";
>   		reg = <0x0>;
>   		spi-tx-bus-width = <1>;